Новичок
Пользователь
Сообщений: 26
Регистрация: 17.7.2007
Из: Yekaterinburg
|
81 12 9 425 091 55 pin break out box 04 14 85 used to troubleshoot electrical systems. See SIB for details x All
81 12 9 425 092 35 pin test cable 04 14 85 used with 425 091 to test systems x All
81 12 9 425 219 diesel timing adapter 04 13 85 used to check ignition timing with 2013 tester - no longer used 524TD
81 12 9 427 785 Sandbags 04 16 86 used for alignment of suspension All
81 12 9 427 824 Exhaust adapters 04 17 87 used to adapt exhaust pipes on M70 to external systems E32
81 12 9 428 828 Exhaust hose 04 29 94 for exhaust pipes E38
81 12 9 428 831 Digital input cable 04 30 96 used in conjunction with 88 pin B.O.B. and DIS x All
81 12 9 428 832 DC circuit breaker cable 04 30 96 used with DIS x All
81 12 9 428 833 25 Bar pressure sensor 04 30 96 used with 90 88 6 117 330 to test system pressures. GT1 sensor throuh Siemens PN A5E00296038 x E36 Newer
81 23 9 415 743 Torx set 04 12 85 no longer available all
81 23 9 415 811 Rivet pliers 04 23 88 used to replace blind rivets. Larger than normal size. No longer available. E32 Newer
81 24 9 408 080 Electrical repair kit I 04 18 82 used to replace connectors x All
81 24 9 408 300 Electrical Repair Kit II 04 02 84 Used to replace connectors x All
81 29 0 426 464 Turbocharger Diagnosis Tool 04 04 07 Starting with the N54 engine, it is necessary to both create a positive and negative pressure in order to test the Turbocharger and its system components. The components that can be tested with this tool are: Air intake check for leaks Wastegate valve for correct function Electro-pneumatic pressure transducer The component tests use Test Module functions in the GT1 and DISplus. A complete examination of the air intake system can only be accomplished using the Turbocharger Diagnostic tool and Diagnosis system. This tool will work on all future Turbocharger systems. Refer to SI for more information. x N54
81 35 0 154 647 50 amp clamp for GT1 04 16 04 The 50-amp clamp is used with the GT1, Measurement Interface Box (SI B08 02 04) and the GT1 Trolley (SI B08 01 04) to conduct accurate closed circuit current measurements (SI B61 08 00) on BMW vehicles. The clamp is attached to MIB port SZ50 (2) and is stored on the Trolley storage rack (8). The 50-amp clamp connector is a push-pull connector and can be removed or installed during testing. x All
81 39 0 393 555 Battery Charger 04 09 07 Alternative charger to the Deutronic. to start the process. MultiCharger 750
81 39 0 428 957 Deutronic Battery Charger
81 42 0 017 566 Lamella curtain 04 08 05 Lamella is a flexible protective barrier used to separate and protect work bays during welding, grinding and sanding. E60-64
81 43 0 020 819 Belt Grinder 04 08 05 Spare grinding belts may be ordered under PN 81 43 0 020 820. E60-64
81 43 0 301 740 Flame coating primer kit 04 08 05 This unit is required to pre-treat surfaces that require aluminum bonding. It uses a special flame coat silicate and primer for the pre-treating. The unit comes with:·Burner Small spatula·Large spatula·CaseConsumable materials are not included with the kit. Refer to group 83 in EPC for refill cartriges and GP-15. x E60-64
81 43 0 301 742 Stud Welder 04 08 05 This highly specialized stud welder operates on 3 phase, 200/460 volts @32 amps. It is required to weld the V2A studs and self-piercing rivets and for the removal of studs and punch rivets. The unit comes with:·Stud welder·2X grounding cables with clamp·Welding gun·500 stainless steel studs·Cart. August 2007 - no longer available through Parts.
81 43 0 301 745 V2A Stud/punch rivet extractor 04 08 05 The service parts for the Rivet gun are available through Reliable Automotive Equipment. (732-747-1770). This unit is used to pull V2A studs and self-piercing rivets out of aluminum parts and to attach special coated blind rivets for repair. The unit comes with:·Rivet gun·2 batteries·Interchangeable head for pulling ·Interchangeable head for attaching Case with charger.
81 43 0 303 336 Rod grinder 04 08 05 Accessory set must be ordered separately. Rod grinder accessory setPN 81 43 0 303 337 E60-64
81 43 0 402 559 Helicoil Plus Thread Repair Kit 04 07 06 NA This special Helicoil plus thread repair kit has been developed to properly repair threads on the magnesium crankcase. Only this kit is to be used to perform repairs on the N52 magnesium crankcase threads. For proper identification, the inserts are colored blue like the aluminum bolts. Refer to repair manual section 11 0 610. Helicoil insert replacement PNs are: 11 11 7 547 538 M6x12, 11 11 7 547 539 M6x15, 11 11 7 547 540 M8X16, 11 11 7 547 548 M12x36 x N52
81 47 0 026 306 Side panel covers 04 02 02 Fiberglass protective covers. All
81 47 0 144 363 Universal front cover 04 02 02 This front cover for the E39 can be joined to the sides by means of the attached reusable fasteners. E39
81 47 0 144 364 Wall Bracket 04 02 02 Used to store the protective covers. All
81 49 0 301 738 Adhesive gun 04 08 05 This is a dual mixture ratio adhesive gun used to apply a specialized 2 component adhesive to the aluminum and steel body parts. Refer to EPC goup 83 for refill cartriges and GP-15. x E60-64
81 49 0 443 166 Pneumatic Adhesive Gun 04 05 08 This tool is used for applying glue to the CFK roof. This tool must be used in conjunction with adhesive set PN 83 19 0 417 144 (not included with gun). E92 M3
81 62 0 301 768 Windshield removal kit 04 26 03 shelf This kit was developed to more efficiently remove windshields with a tight body to windshield gap. The kit uses a round cutting wire, which is placed around the window on the outside then pulled inwards and rolled up on a spindle. The adhesive is cut as the wire is wound up on the spindle.The kit consists of:Tool case,Cable winch with suction cup,Cutting wire for ~100 applications,Protective goggles and gloves,Plastic vehicle interior protection,Tool case with chisel, wire starter, ratchet, extension, trim tool,Instructions. Refer to repair manual section 51 31. Order replacement wire under PN 81 62 0 390 402. New improved kit under PN 81 62 0 397 332/333. Cold urethane PN 83 19 0 152 031 or complete kit under PN 83 19 0 147 369.
81 62 0 404 083 DK LAN Cable 07 02 05 The cables work on the Diagnostic heads and the OPS/OPPS.
81 62 0 410 436 Scraper set 04 23 05 This scraper set will remove window sealant residue or engine gaskets efficiently. The kit consists of the following:1. Handle2. 10 blades 12 mm wide (81 62 0 410 806)3. 10 blades 16 mm wide (81 62 0 410 807)4. 10 blades 20 mm wide (81 62 0 410 808) All
81 64 0 142 874 Torque wrench 04 29 03 shelf Used with various BMW square drive attachments to accurately torque fittings. This model covers torques from 2-100 nm. Replacement battery ordered under PN 81 64 0 417 654. All
81 64 0 142 875 Torque wrench 04 29 03 shelf Used with various BMW square drive attachments to accurately torque fittings. This model covers torques from 20-200 nm.Replacement battery ordered under PN 81 64 0 417 654. All
81 64 9 424 055 Hazet Square Drive Set 04 03 03 Used in conjunction with a square drive torque wrench (not included (refer to 04 04 03) to torque vehicle bolts. R50/53
81 64 9 429 218 Body panel tool set 04 08 05 This tool set is used to repair body damage to the outer panels. The set does not included the toolbox pictured E60-64
81 64 9 429 291 Tool storage cart 04 08 05 Used to store all of the outer body and structural tools. Cart includes drawer partitions but does not include the tools shown. E60-64
82 11 1 466 971 Radio Tool This is the red handled, 5 sided radio removal tool. All
82 11 9 408 400 Electrical repair kit III 04 03 88 connector kit x E32 Newer
83 30 0 131 100 170 009 Coolant tank test flange 04 17 89 C3 used with pressure tester to test coolant system for leaks x E30
83 30 0 420 667 Alcohol Detection Test Tool 13 04 06 In order to correctly diagnose various drivability complaints caused by fuel blends with a high level of ethanol content, BMW has developed an alcohol detection test tool. x All
83 30 0 433 207 Evaporative System Test Adapter 04 20 07 To be used in conjunction with approved VACUTEC Smoke Machine evaporative leak testing device x All Models
83 30 0 490 075 000 200 Cross Member This tool is used to support the engine when removing and replacing transmission or transaxle. Consists of: 1. 000 201 (83 30 0 490 076)Locating bridge 2. 000 202 (83 30 0 490 077)Spindle with hook 3. 000 203 (83 30 0 490 078) Extension Note: for extending locating bridge 000 201 Model series: E65 4. 000 204 (83 30 0 490 079) Adapter support In conjunction with 000 200 5. 000 205 (83 30 0 490 080) Extension Note: Model series R50, R53 6. 000 206 (83 30 0 490 081)Support foot (2x) Note: Model series: E30, E31, E32, E34, E36, Z3 6-cylinders only 7. 000 207 (83 30 0 490 082 Support foot (2x) Note: Model: Z3/4-cylinder engines only 8. 000 208 (83 30 0 490 083)Support foot (2x) Note: Model series: E38, E39, E46, E60, E65 9. 000 209 (83 30 0 493 123)Chain with hook Note: Version as 110 003 10. 000 451 (83 30 0 494 449)Profile strip Note: Model series: E85 11. 000 452 (83 30 0 495 850)Supports (2x) Note: Model series: E70 In conjunction with: 000 208 All
83 30 0 490 083 000 208 Support feet 04 16 97 used with 88 88 6 000 200 to support engine during work All Earlyxcept Z3
83 30 0 490 110 001 450 Engine stand 04 17 87 used to mount engine for rework x All
83 30 0 490 115 001 460 Engine supports 04 17 87 used to mount engine on stand 88 88 6 001 450 x M70
83 30 0 490 133 002 030 Transmission Stand Used with the transmission fixtures to R&R transmissions. Fixtures not included with stand. ALL
83 30 0 490 135 002 040 Universal support 04 18 91 used to support rear suspension for removal x All Earlyxcept Early31
83 30 0 490 147 002 110 T30 torx insert 04 15 85 Used to R&R sensor on wheel well x E23
83 30 0 490 149 002 130 T25 Torx driver 04 14 88 A7 used to remove seat trim panels x E32
83 30 0 490 150 002 140 T20 torx bit 04 18 94 used to remove headlight lenses x E38
83 30 0 490 152 002 180 6mm hex socket 04 22 88 A7 this keyed socket is needed to remove the distributor rotor x M70
83 30 0 490 169 002 490 Adapter 04 08 88 B13 used with 88 88 6 002 500 and 88 88 6 002 510 for brake rotor runout measurments x All
83 30 0 490 185 002 530 Measuring bridge 04 01 84 used with 88 88 6 002 210 to measure piston projection lenght x 524TD
83 30 0 490 186 002 540 Injection nozzle tester 04 01 84 used to test injector spray pattern x 524TD
83 30 0 490 441 004 210 Reamer kit 04 18 87 used to ream valve guides. See SIB 11 11 86 for details x S38
83 30 0 490 466 005 010 Puller 04 01 84 used to remove shaft sealing rings on engine and trans. x 524TD
83 30 0 490 473 005 030 Seat belt pliers 04 12 89 B13 used to replace seat belt button (parst fiche) x All
83 30 0 490 474 005 040 Seat belt button press Used to fasten the seat belt stop button on new belts. All
83 30 0 490 475 005 500 Handle A18 used with various drifts to install seals x All
83 30 0 490 478 005 591 Module puller 04 21 88 A13 used to remove modules such as ZKE. Replaces 88 88 6 005 590 x E32 Newer
83 30 0 490 480 005 600 Gas spring compressor 04 14 88 A6 used to compress gas springs on the E30 seats E30
83 30 0 490 482 007 500 Puller set C6 used to remove various bearings x All
83 30 0 490 483 007 501 Puller spindle B6 used with 007 500 x All
83 30 0 490 490 008 000 Hydraulic press 04 13 01 Shelf Used to R&R bushings. Refer to SIB 04 13 01. Replacement PN for 008 006 is 83 30 0 493 412. All
83 30 0 490 497 008 550 Puller used to remove rear wheel bearing x E24
83 30 0 490 502 009 100 Wrench 04 25 86 1 used to adjust the headlight cleaning system jets x 750i, E32
83 30 0 490 504 009 120 Torque angle tool 04 21 96 used to adjust torque angle on head bolts x All
83 30 0 490 505 009 150 Sealing pliers 04 08 89 C2/C3 Used to place lead seal on final drive Lead seal 62 121 354 984. Wire 62 121 354 983. E30
83 30 0 490 508 009 190 Pliers 04 22 92 B6 cuts off timing chain cover gasket x M60
83 30 0 490 509 009 200 Adjustment tool 04 03 90 C14 used to adjust windshield washer nozzles. Tip only 88 88 6 009 201 x E32 Newer
83 30 0 490 512 009 220 Wiper arm adjustment tool 04 51 01 A21 Used with 009 331 to adjust the approach angle of the wiper arms. x E53
83 30 0 490 513 009 230 Wiper adjustment gauge 04 14 95 A21 used to adjust the angle of the wiper arm x All
83 30 0 490 515 009 250 Torque wrench 04 12 96 A21 used for low torque aplications such as chain tensioner adjustment x M62
83 30 0 490 518 009 260 Wiper arm adjuster 04 28 96 A21 used with 90 88 6 009 230 to adjust wipers x E39
83 30 0 490 525 009 280 Navigation calibrator 04 31 96 A21 used with 88 88 6 009 200 to calibrate nav system E39
83 30 0 490 526 009 300 Grill removal tool 04 09 97 A21 used to remove dash vents. x E39
83 30 0 490 527 009 310 Wedge kit 04 09 97 used to remove the vehicle body parts without damage All
83 30 0 490 566 110 010 Spacer 04 16 90 C7/C8 used to support engine with trans removed E31
83 30 0 490 567 110 020 Engine lifting bar Used to remove the 6 cylinder engines from the vehicle. x M52/54/30/20, N52/62, S85
83 30 0 490 573 110 030 Adapter 04 07 91 A4 used with 88 88 6 110 020 to remove M50 engine x E36
83 30 0 490 587 110 090 Mounting plate 04 06 90 used to mount engine on stand x M42
83 30 0 490 588 110 100 Engine adapter plate Used on 4 cylinder engines up to 1979. 4 cylinder
83 30 0 490 589 110 110 Engine plate 04 01 84 used with engine stand to support engine x 524TD
83 30 0 490 590 110 120 Adapter plate 00 03 80 used to mount engine on stand x E23
83 30 0 490 591 110 130 Adapter plate Used to mount the engine to the engine stand. 530i
83 30 0 490 593 110 160 Compression gauge 04 01 84 used to record compression of engine x 524TD
83 30 0 490 599 110 166 Adapter hose 04 14 88 A5 used with 88 88 6 110 160 to test compression x M70
83 30 0 490 601 110 180 Valve board 04 17 87 used to hold the valves in possition during removal x M70
83 30 0 490 613 110 220 Compression test kit Used to test and record engine cylinder compression. Paper for compression tester #110 229, order PN 83 30 0 490 622. All
83 30 0 490 619 110 226 Compression test hose Used with the 25 bar DISplus pressure sensor to test engine compression. All
83 30 0 490 627 110 240 Coupling Used to adapt test probes to pressure gauge All
83 30 0 490 649 110 343 Valve spring hook 04 14 96 used to hook the valve spring in the depressed possition x M52
83 30 0 490 650 110 344 Valve spring compressor 04 14 96 used to depress the valve spring with 90 88 6 110342 x M52
83 30 0 490 651 110 345 Valve spring depressor 04 04 96 used to compress the valve springs x M44
83 30 0 490 653 111 010 Pressure testing set 04 19 86 used to pressure test the cylinder head x S38
83 30 0 490 691 111 050 Assembly accessories 04 19 86 used with 88 88 6 111 060 to remove valve springs x S38
83 30 0 490 708 111 072 Retaining bracket 04 09 95 used to attach cylinder head to 88 88 6 111 065 x E38 With M73
83 30 0 490 712 111 110 Pressure fixture 04 19 86 used with 88 88 6 111 012 to pressure test the head x S38
83 30 0 490 722 111 180 Spanner 04 01 84 used on drag lever bolts x 524TD
83 30 0 490 724 111 200 Mandrel 04 04 86 B5 used to install grooved valve stem seals. Replaces 88 88 6 111 070/080/090/140/160/170 x All
83 30 0 490 725 111 210 Oil seal puller 04 17 87 A18 used to remove the front crankshaft oil seal x M70
83 30 0 490 726 111 220 Drift 04 17 87 B15 used to press in the crankshaft oil seal -timing case cover x M70
83 30 0 490 727 111 230 Drift 04 17 87 B15 use to drive in the crankshaft oil seal into the end cover x M70
83 30 0 490 728 111 250 Pliers B15 used to remove valve stem seals x All
83 30 0 490 729 111 260 Drift used to install seals x E21
83 30 0 490 734 111 280 Drift used to install seals in fron t cover x E23, E30, E24, E28
83 30 0 490 746 111 380 Sleeve 04 01 84 used to install valve shaft seals x 524TD
83 30 0 490 752 111 410 Alignment tool 04 12 96 B14 used to correctly align valve cover x M62
83 30 0 490 755 111 420 Pressure fixture 04 21 88 used to pressure test engine head M70
83 30 0 490 761 111 430 Pressure fixture 04 06 90 used to pressure test the head M42
83 30 0 490 771 111 440 Valve support tray 04 06 90 used to support valves during removal x M42
83 30 0 490 774 111 450 Pressure fixture 04 16 90 used with 88 88 6 111 430 to pressure test heads M50
83 30 0 490 798 112 000 Puller B15 used to remove the front crank sprocket x 2500
83 30 0 490 804 112 006 Base plate 04 09 95 B15 used with 88 88 6 112 000 to remove crankshaft sprocket E31,E38
83 30 0 490 805 008 510 Puller A1/B1 used to push out bearings and shafts. Replaced by 88 88 6 112 010. x All, E24
83 30 0 490 811 112 016 Spindle 04 22 92 A20/B20 used with 88 88 6 112 010 to remove pilot bearing on the crankshaft x M60
83 30 0 490 818 112 030 Drift B9 used to install rear bearing - flywheel x E28
83 30 0 490 819 112 040 Holder 04 01 84 used to hold intermediate shaft x 524TD
83 30 0 490 820 112 050 Guide 04 01 84 used to install pistons x 524TD
83 30 0 490 821 112 060 Guides 04 19 86 A9/B9 used to install the pistons x S38
83 30 0 490 822 112 070 Flywheel holder 04 17 87 A16 used to hold flywheel when loosening bolts x M70
83 30 0 490 825 112 100 Flywheel lock used to hold flywheel on standard transmission x E21
83 30 0 490 835 112 120 Flywheel lock C2 used to hold flywheel on automatic transmission x 2000, 2500, 3.0
83 30 0 490 836 112 130 Extension spindles C11 used to pull hub and toothed gear x E28
83 30 0 490 841 112 150 Holder A2/B2 used to hold front dampner for removal x E28
83 30 0 490 842 112 160 Flywheel lock A4 used to hold flywheel x 2500
83 30 0 490 843 112 170 Flywheel lock B4 used to hold flywheel x E28
83 30 0 490 845 112 190 Holder C22 used to hold camshaft and intermediate shaft x E28
83 30 0 490 849 112 210 Seal guide used to guide crankshaft seals during instalation x E24
83 30 0 490 854 112 230 Holder 04 17 87 A21 used to hold vibration damper when R and R damper bolt (front) x M70
83 30 0 490 855 112 240 Holder 04 02 90 3 used to hold vibration damper in order to tighten x E34, E32
83 30 0 490 856 E12 Torx 04 06 90 A22/B22 used to R and R cylinder head bolts x M42
83 30 0 490 858 112 270 Assembly pliers 04 19 86 B21 used to install the pistons x S38
83 30 0 490 859 112 280 Counter holder 04 15 88 A23 used to hold drive belt and sprocket to remove retaining bolt x M20
83 30 0 490 861 112 300 Arbor 04 01 84 used to lock flywheel x 524TD
83 30 0 490 862 112 310 Seal extractor 04 06 90 A23 use to remove front radial oil seal x M42
83 30 0 490 865 112 313 Thrust pad 04 06 90 A23/A24 used with 88 88 6 112 310 to remove crankshaft seal x M42
83 30 0 490 867 112 330 Assembly plate 04 06 90 C21 used to assemble lower timing case x M42
83 30 0 490 868 112 340 Bearing extractor 04 13 90 B22 used to remove the crankshaft bearing x E31
83 30 0 490 873 112 350 Drift 04 13 90 B23 used to install the crank guide bearing x E31
83 30 0 490 876 112 380 Seal puller 04 22 92 B23 removes timing case cover seal x M60
83 30 0 490 882 112 390 Seal installer 04 22 92 B23 installs crankshaft end cover with seal x M60
83 30 0 490 883 112 400 Tensioner block 04 22 92 used with 90 88 6 113 390 when timing case is removed x M60
83 30 0 490 884 112 410 Spacer 04 14 96 B22 used with 88 88 6 112 150 to maintain counter pressure when removing crankshaft x M52
83 30 0 490 885 112 420 Crankshaft holder 04 09 95 B23/C23 used to hold the crank. when R and R central nut x E31 With M73,E38 With M73
83 30 0 490 886 112 430 Camshaft insertion jig 04 22 92 A22 used to check camshaft possition after insertion x M60
83 30 0 490 887 112 440 Camshaft Jig 04 22 92 shelf used toadjust camshaft x M60
83 30 0 490 892 112 445 Camshaft jig 04 02 94 used with 90 88 6 112 440 to align camshaft. See SIB for details x M60
83 30 0 490 893 112 446 Camshaft jig 04 02 94 used to align camshaft. See SIB for details x M60
83 30 0 490 894 112 450 Crankshaft holder 04 22 92 A24 used to hold crank to remove central bolt x M60
83 30 0 490 896 112 470 Alignment rods 04 22 92 A24 used to properly align connecting rods during replacement x M60
83 30 0 490 897 112 480 Engine support 04 04 93 used to support the engine with transmission removed x E32
83 30 0 490 900 113 010 Camshaft fixture 04 19 86 used to R&R the camshaft x S38
83 30 0 490 901 113 020 Crank turner 04 19 86 A24 used to turn the crankshaft x S38
83 30 0 490 902 113 030 Tray 04 19 86 A23/A24 used to store valve tappets x S38
83 30 0 490 903 113 040 Special Bolt 04 19 86 B22 used to remove the guide pulley (timing chain) x S38
83 30 0 490 912 113 080 Drift 04 01 84 used to install seal ring on camshaft x 524TD
83 30 0 490 913 113 090 Holding fixture 04 01 84 used to hold camshaft x 524TD
83 30 0 490 928 113 120 Lever installer 04 01 84 used to install drag lever in head x 524TD
83 30 0 490 931 113 130 Valve device 04 01 84 used to R x 524TD
83 30 0 490 937 113 140 Puller 04 01 84 used to remove ball pin in cylinder head x 524TD
83 30 0 490 942 113 160 Valve adjuster 04 19 86 A24 holder with gauge to adjust valves. This PN only contains 5 gauges. If you want all 7 gauges you must order the PN above and PN 83 30 0 493 754. x S38
83 30 0 490 945 113 170 Valve lever 04 19 86 B22/C22 used to press down valve tappets when adjusting valves x S38
83 30 0 490 946 113 180 thrust lever 04 17 87 used to R&R the rocker arms in the cylinder head x M70
83 30 0 490 947 113 190 Alignment tool 04 17 87 A23 used to align ca x M70
83 30 0 490 948 113 200 seal driver 04 27 87 A23/A24 used to install the upper timing case cover seal x M70
83 30 0 490 949 113 210 Centering bushing 04 27 87 A10/A11 used to center the timing case cover on the camshaft x M70
83 30 0 490 950 113 220 Guide sleeve 04 27 87 A13 used to guide the case cover onto the camshaft x M70
83 30 0 490 951 113 230 Degree scale 04 02 90 C10 used with 88 88 6 12 240 to tighten central nut on crankshaft6 x E34
83 30 0 490 952 113 240 Camshaft locating fixture 04 06 90 A6 used with 88 88 6 112 300 to align and hold camshafts x M42
83 30 0 490 956 113 250 Suction cups 04 06 90 A7 used to remove hydralic lifters. 88 88 6 113 251 was later added to included the M50. x M42
83 30 0 490 957 113 251 Suction cups 04 11 90 used with 88 88 6 113 250 to remove hydraulic lifters x M50
83 30 0 490 959 113 260 Camshaft jig 04 06 90 Used to hold the camshaft when removing the camshaft bearing caps. M50 M52, M54 S52, M42
83 30 0 490 961 113 262 Holding bolts 04 06 90 Used on 113 260 to hold camshaft when removing the camshaft bearing caps. M50 M52 M54 S52
83 30 0 490 962 113 270 Camshaft removing fixture 04 11 90 used with 88 88 6 113 260to remove camshaft x M50
83 30 0 490 965 113 280 Seal installer 04 11 90 B2 used to install timing case seal x M50
83 30 0 490 966 113 290 Securing spring 04 11 90 C3 used to hold chain tensioner when R and R timing case cover x M50
83 30 0 490 968 113 292 Locking pin 04 07 95 A2 used to lock the secondary chain tensioner x M52
83 30 0 490 969 113 300 Mounting plate 04 11 90 used to mount engine to engine stand x M50
83 30 0 490 970 113 310 Cam chain clips 04 12 96 B4 used to secure the cam chain tensioner x M62
83 30 0 490 973 113 340 Locking Pins Used to lock the chain tensioner in place during R&R of the cylinder head. N54 N73 M62
83 30 0 490 981 113 380 T50 torx socket 04 14 92 A2 used to R x M70
83 30 0 490 982 113 390 Timing chain tensioner 04 22 92 A10 places proper tension on timing chain during engine assembly x M60
83 30 0 490 988 113 410 Valve Board 04 11 03 shelf Used to R and R cylinder head valves and valve springs. x E46 M3
83 30 0 490 992 113 420 Cam clips 04 22 92 B10 locks secondary chain tensioner during repairs x M60
83 30 0 490 993 113 430 Camshaft turning tool 04 22 92 B6 used to safely turn the camshafts x M60
83 30 0 490 994 113 440 Vibration damper fixture 04 22 92 C11 used to prevent contact between pistons and head when replacing the heads x M60
83 30 0 490 995 113 450 Adapter block 04 27 92 B5 used with 126 410 to measure VANOS angle x TU, M50
83 30 0 490 996 113 460 Angle disc 04 28 92 B4 measures torque angle on the M60 when tightening crankshaft x M60
83 30 0 490 999 113 490 Reference gauge Used to set Vanos when installing. S50B30 S50B32
83 30 0 491 002 114 020 Oil filter wrench 04 08 83 C8 used to remove oil filters x M10, M20
83 30 0 491 003 114 030 Connection nipple 04 05 88 B5 used to check oil pressure x E34
83 30 0 491 005 114 050 Reducer Used to connect 136 054 to pressure gauge for checking oil pressure All
83 30 0 491 007 114 070 Assembly tool 04 19 86 C11 used to drive in oil dipstick tube x S38
83 30 0 491 011 114 110 Alignment studs 04 04 96 A3/B3/C3 used to hold and align gasket for upper timing case x M44
83 30 0 491 015 114 150 Drift C1 used to install radial oil seals on timing case cover x M44
83 30 0 491 018 114 180 T60 torx socket 04 12 94 C1 used to remove dual mass flywheel bolts x M60
83 30 0 491 019 114 190 Timing chain adapter 04 18 94 B11 used to pretension timing chain x E38
83 30 0 491 025 114 220 Chain tensioner 04 07 95 B4 used to tension primary chain x M52
83 30 0 491 047 115 040 Special wrench 04 20 87 B4 used to tighten viscous fan clutch x All
83 30 0 491 048 115 050 Fan pulley holder 04 06 90 B12 used to hold front pulley to remove x M42
83 30 0 491 056 115 100 Adapter with wrench Used to turn engine at crankshaft when adjusting valve timing. S50B30, S54, S50B32
83 30 0 491 057 115 110 Crankshaft seal installer 04 09 95 A11 usd to install the front crank seal x E31 With M73,E38 With M73
83 30 0 491 058 115 130 Valve depressor 04 04 96 C12 used to depress valves x M44
83 30 0 491 062 115 490 Chain tensioner 04 17 94 A5 Used to remove the VANOS adjustment unit x M3, E36
83 30 0 491 069 116 060 Special extension 04 17 87 A5 used to R&R intka emanifold nuts x M70
83 30 0 491 070 116 070 Universal socket 04 02 90 A5 used to R and R exhaust manifold x E34
83 30 0 491 073 117 010 Hose 04 01 84 for checking control valve x 524TD
83 30 0 491 074 117 020 oxygen sensor socket 04 04 85 used to R&R O2 sensor all
83 30 0 491 078 117 310 Engine support 04 09 95 used to support engine with trans. removed x E38 With M73
83 30 0 491 079 117 320 Oil jet adjuster 04 04 96 A5 used to adjust the crankcase oil jets x M44
83 30 0 491 080 117 330 Oil pressure adapter 04 04 96 A5 used to measuer oil pressure using 90 88 6 136 050. x M44
83 30 0 491 086 117 342 Locking pin 04 28 01 A5 Used with 119 130 to lock the camshaft during assembly. x E46 M3
83 30 0 491 089 117 370 Engine spacer 04 02 96 C4 used to support engine with trans. removed x E39
83 30 0 491 090 117 380 Torque block 04 12 96 A5 use to adj. timing chain tensioner when timing cover is off. x M62
83 30 0 491 091 117 450 Oxygen sensor tester 04 04 94 used to test oxygen sensor operation x all
83 30 0 491 101 118 000 Valve remover 04 19 86 A5/B5 used with 88 88 6 111 052 to remove valves x S38
83 30 0 491 109 118 040 Support Plate Used in conjunction with 001 450 to secure engine to engine stand. M50,M52,M54,M56,S54
83 30 0 491 115 121 080 Ignition wire repair kit used to repair ignition wires. Replaces 112 090 x E38
83 30 0 491 118 121 083 Replacement crimping jaws 04 24 94 A5/B5 used to crimp 4mm flat connectors with 88 88 6 121 091 x E38
83 30 0 491 123 121 090 crimping pliers 04 01 84 used to crimp spark plug wires - crimper 88 88 6 121 091, pliers -88 88 6 121 092 x e23 e24
83 30 0 491 127 121 160 Spark plug socket 04 19 86 A5 used to R and R spark plugs x S38
83 30 0 491 128 121 170 Socket and torque converter 04 17 87 A5 used to R and R the spark plugs - 121 171 and 121 172 M70
83 30 0 491 131 121 180 Plug pliers 04 21 88 A5 used to remove spark plug pliers All
83 30 0 491 133 121 200 Torque limiter 04 22 92 A5 used with 88 88 6 121 171 to tighten spark plugs to propper torque x M60 EarlyNG
83 30 0 491 134 121 300 134 pin B.O.B and adapter cable set 04 14 97 shelf used to diagnose problems in control modules. x E46
83 30 0 491 148 126 410 Adapter lead 04 27 92 Actuates VANOS unit for testing x TU
83 30 0 491 151 127 010 EML test adapter 04 17 87 used to test the external safety path x ALL
83 30 0 491 152 161 160 Tank ventilation leak couplers 04 01 98 B20 used to test tank vent system for leaks in conjunction with 90 88 6 161 150. x E38,E39
83 30 0 491 153 127 012 EML cable adapter 04 16 91 Replaced by 90 88 6 127 013 x All
83 30 0 491 154 127 013 EML safety path adapter 04 03 94 used to test the EML safety path on vehicles from MY93 x E31 M70
83 30 0 491 156 127 020 Primary adapter 04 01 91 displays primary voltage on scope x E30 Newer
83 30 0 491 158 127 030 Secondary adapter 04 16 91 measures secondary voltage x M50
83 30 0 491 160 127 040 Coil tester 04 25 92 allows you to read scope patterns on coils. See SIB for details x M42 Newer
83 30 0 491 167 127 320 23 Pin test cable 04 05 02 Used in conjunction with the DISplus and BOB 614 390 to troubleshoot the Valvetronic control module. x E65, E31,E36, E38
83 30 0 491 168 127 130 Extension 04 09 95 A9 used with 88 88 6 121 171 and 90 88 6 121 200 to remove spark plugs E38, E31
83 30 0 491 223 130 110 Sampler tubes 04 14 92 used to test CO levels with Gas Bench x S38
83 30 0 491 250 131 100 Allen screwdriver 04 08 83 used to adjust CO on L Jet x E23, E24, E28
83 30 0 491 254 132 010 Wrench 04 01 84 used to tighten heater element in the fuel filter x 524TD
83 30 0 491 256 133 010 Hose clamp 04 08 81 A9 used to close off hoses for testing x All
83 30 0 491 264 133 065 Adapter Connection adapter for fuel system. All except N73
83 30 0 491 270 134 010 Bridging tool 04 16 87 C1 connects to throttle switch plug to ensure proper signal to the control module while adjusting idle x E30, E28, E24
83 30 0 491 272 134 030 Current Generator 04 16 85 required for basic adjustment of the idle control valve x E30
83 30 0 491 276 135 010 puller 04 01 84 used to pull inj, pump impeller x 524TD
83 30 0 491 277 135 020 Wrench 04 01 84 used to R&R injection lines x 524TD
83 30 0 491 285 135 060 Tool set 04 11 85 used to replace the injector pump x 524TD
83 30 0 491 305 135 220 Fuel pressure adapter 04 04 96 used to measure fuel pressure at rail x M44
83 30 0 491 310 135 270 Fuel pressuer adapter hose 04 09 97 used with DIS to test fuel inlet pressure. x M62
83 30 0 491 313 135 280 Line plugs 04 09 97 C3 used to plug the fuel lines during testing M62
83 30 0 491 316 135 300 Exhaust pick-up 04 02 82 used to test CO x All Early
83 30 0 491 318 135 320 Socket 04 01 84 use to R&R injectors x 524TD
83 30 0 491 319 135 330 Gauge holder 04 01 84 used to hold measurment gauge x 524TD
83 30 0 491 320 135 340 Alignment pin 04 01 84 used to align injection pump with impeller x 524TD
83 30 0 491 340 136 050 Pressure sensor adapter set 04 30 96 Used with 81 12 9 428 833 to test pressures x E36 Newer
83 30 0 491 369 161 020 Fuel sender spanner used to remove nut on sender. Aluminun tools must use steel jaws pn 161 022 x all
83 30 0 491 370 161 030 Pin wrench 04 13 90 B14 used to R and R locking pin on gas filler door x E31
83 30 0 491 371 161 040 Spreading tool 04 05 93 C3 used to remove vent pipe on carbon canister M50
83 30 0 491 372 161 050 Charcoal canister line remover 04 18 94 B9 releases canister line x E38
83 30 0 491 374 161 150 Evap. system leak tester 04 06 97 test for leaks in the evaporative syatem. used in conjunction with 25 bar pressure sensor 04 30 96. x Z3
83 30 0 491 384 170 000 Coolant system pressure tester A2/B2 used to test coolnt system pressures. Replaced by PN 90 88 6 170 100 and 130. x All
83 30 0 491 389 170 005 Cooling system adapter 04 25 86 B3/C3 used with 88 88 6 170 000 to check cooling system for leaks x E32
83 30 0 491 391 170 009 Coolant tank test flange 04 17 89 B7 used with pressure tester to test coolant system for leaks x M3
83 30 0 491 395 170 013 Rubber seal 04 19 93 rebuild part for 88 88 6 170 002 All
83 30 0 491 396 170 014 Rubber valve 04 19 93 rebuild part for 88 88 6 170 002 All
83 30 0 491 399 170 017 Leather pump 04 19 93 rebuild part for 88 88 6 170 002 All
83 30 0 491 417 212 070 Clutch Gauge 04 07 91 used to measure clutch wear - replaced be tool 90 88 6 212 080 x E36
83 30 0 491 418 212 080 Clutch depth gauge 04 16 96 C12 used to check disc wear - replaces tool 88 88 6 212 070 x All
83 30 0 491 421 212 100 Mandrel Used to center the clutch disc while installing the clutch. 265
83 30 0 491 423 212 120 Clutch alignment pin 04 13 90 B3 used to align clutch during installation x E31
83 30 0 491 424 212 130 Clutch alignment tool 04 11 91 C3 used to align clutch during installation x M50, M42
83 30 0 491 425 212 140 Clutch alignment tool 04 03 97 used to center and align clutch. x E34,E36, E39
83 30 0 491 428 212 150 self adj. clutch reset tool 04 03 97 used to reset SAC during instillation. Do not use this tool, refer to SI B04 14 01. x E39
83 30 0 491 435 215 030 Clutch bleeder tool 04 12 97 used to bleed the clutch slave cylinder E34, E36, E38, E39, E38
83 30 0 491 440 230 020 Holder used on all 3 and 4 hole flanges x All
83 30 0 491 442 230 040 Transmission cradle 04 01 91 used to support trans. E31
83 30 0 491 454 230 490 Transmission seal puller 04 12 97 A6 used to remove input shaft seals. x E39, E31,E34,E36
83 30 0 491 457 231 000 Installer used to install gearbox housing bearings x E12,E21,E28,E30,E32, E34
83 30 0 491 497 231 200 Guide bushing B7 used with 231 210 for centering x All
83 30 0 491 498 231 210 Socket 30/83 A22 used to R and R gearbox output flange x All
83 30 0 491 507 231 300 Installation tool A20/B20 used to install ZF input and output shaft bearings x All
83 30 0 491 509 231 302 Rear axle press adapter 04 18 94 22 1 018 used to press on final drive flange with 88 88 6 231 300 and 88 88 6 331 341 x E38
83 30 0 491 511 231 320 Holding wrench 04 03 84 used to hold output flange to remove nut x E23,E24,E28, E30
83 30 0 491 512 231 330 Spacer 04 02 90 22 1 019 used to support rear of engine when trans is removed x E34
83 30 0 491 518 231 360 Drift C8 used with 005 500 to fit output shaft seals x E30, E28
83 30 0 491 519 231 370 Drift C7 used to install radial oil seal Getrag trans x E34, E21,E23,E28,E30,E32
83 30 0 491 559 232 150 Bearing installer used to install front tapered roller bearing in 260 and 245 trans x E32,E34,E36,E38, E39
83 30 0 491 570 232 260 Drift 04 09 98 B8/C8 installs the selector shaft seal on the SSD 310D transmission x M50, E34, M50
83 30 0 491 578 232 300 Drift 04 09 91 installs the output shaft seal on the SSD 310Z transmission x E34, M50
83 30 0 491 580 232 320 36 mm socket 04 19 91 used to R and R output flange nut on manual transmission x 525i, E34
83 30 0 491 582 232 340 Drift 04 09 98 232 340 installs the input shaft seal on the SSD 310Z transmission x M50, E34
83 30 0 491 595 232 470 Drift 04 22 93 C10 used to install lock ring on output flange E31
83 30 0 491 596 232 480 Drift 04 22 93 C24 used to install output shaft seal E31
83 30 0 491 597 232 490 Drift 04 22 93 C24 used to install input shaft seal E31
83 30 0 491 600 233 010 Press 04 22 93 C24 used to press output flange E31
83 30 0 491 604 233 020 Installer 04 22 93 B24 used to install the bellows on the gear shift lever E31
83 30 0 491 605 233 030 Support plate 04 18 94 C24 supports trans. with engine removed x E38
83 30 0 491 606 233 100 Transmission cup tool 04 16 95 C4 used to R and R the 3rd and 4th gear locking pins on the S5D 310Z x M3,E36
83 30 0 491 618 240 020 Adapter set B2/C2 used to test oil pressure in all automatic transmissions x All
83 30 0 491 627 240 029 pressing adapter 04 06 82 used to check transmission pressure x e23 e21
83 30 0 491 628 240 030 Pressure adapter C9/C10 used to test main oil pressure on 4HP 22 transmission x E30,E32,E34,E36
83 30 0 491 633 240 050 Puller C10 used to remove sealing plugs in 3HP 12/20/22 and 4HP 22/24 x E12,E21,E30,E23,E34,E36
83 30 0 491 639 240 110 Seal installer 04 09 90 used to install front radial oil seal on 4HP22/24 transmissions x E30,E31, E34
83 30 0 491 642 240 130 Transmission adapter 04 17 87 used to adapt 4hp 22 and 4HP 24 to stand E34
83 30 0 491 643 240 140 Trans. pressure adapter 04 14 92 A1 used to check pressure on A4S 310R. See SIB for details x E36
83 30 0 491 645 240 151 Pressure screw 04 07 93 used with 88 88 6 240 150 to support trans for reworking E34
83 30 0 491 651 240 170 transmission support 04 34 92 used to support the A5S560Z transmission during R&R. all
83 30 0 491 652 240 180 Support Used to mount engine to the assembly stand. NLA - replaced by 240 200 - 83 30 0 495 446. A5S560Z, 310Z,325Z,360R
83 30 0 491 661 240 250 Transmission support 04 32 96 used t support A5S 440Z trans. E39
83 30 0 491 667 241 110 Magnetic socket 04 25 86 A15/A16 used to R and R flywheel bolts x E32
83 30 0 491 668 241 120 Alignment tool 04 22 96 A15/A16 used to align transmission selector switch x E39
83 30 0 491 670 241 170 Spanner 04 07 93 A15 Used to R and R the nut on the output flange A5S 310Z x E34
83 30 0 491 671 241 180 Assembly tool 04 07 93 A16 used to mount the oil pump housing E34
83 30 0 491 672 241 190 Drift 04 07 93 A16 Used to install the output flange seal x E34
83 30 0 491 673 241 200 Mounting sleeve 04 07 93 A16 Used to properly install the radial oil seal on the selector shaft x E34
83 30 0 491 675 241 220 Support 04 07 93 shelf used to support the output flange housing E34
83 30 0 491 690 241 290 Seal Installer wedges Used to install seal. GM5
83 30 0 491 705 242 300 Holder 04 01 92 6 holds torque converter to flywheel when replacing transmission x M30, M50
83 30 0 491 709 243 140 Pump turner B15 used to turn oil pump on 3HP 12/22 x E36, E38,E12,E21,E23,E24,E28,E30,E31,E32,E34
83 30 0 491 715 244 000 Fitting handle B16 used to install torque converters x All
83 30 0 491 720 244 044 Hold down bolts 04 17 87 used to check torque converter for leaks E30,E31,E32, E34
83 30 0 491 731 244 130 Clamping tool 04 09 97 A24 used to clamp torque converter during R and R All
83 30 0 491 758 245 120 Centering tool 04 01 95 Repairs delayed engaugement on A4S 310R. Refer to SIB 24 05 94 x E34, E36
83 30 0 491 763 245 150 Alignment pins 04 12 90 B24 used to center valve body on THMR 1 x Z3, E34,E36,E39
83 30 0 491 764 245 160 Alignment pins 04 13 93 B17 used to maintain proper alignment of trans case during assembly E36,E34
83 30 0 491 767 245 190 Pressure adapter 04 12 90 used with 88 88 6 240 021 to test main pressure on THMR 1 trans. x E34,E36,E39, Z3
83 30 0 491 768 245 200 Driving mandrel 04 12 90 B12 used to replace the radial seal onthe THMR 1 shift shaft x Z3, E34,E36,E39, E34
83 30 0 491 769 245 210 Holder 04 22 92 B12 used to R and R the trans shift cable on the 4HP 22/24, A5S 310R/Z x E36, E34,E32,E31,E30
83 30 0 491 771 245 230 seal installer 04 02 92 used to install the shift shaft seal x 4HP22/24
83 30 0 491 773 245 250 Seal installer 04 08 95 B12 used to install shift shaft seal on A5S 560Z x E34, E31,E38
83 30 0 491 774 245 260 Seal puller 04 08 95 B12 removes shift shaft seal x E38,E34,E31
83 30 0 491 775 245 270 Seal driver 04 32 96 A14 used to installl the shift shaft seal on the A5S 440Z trans. x E38,E39
83 30 0 491 776 245 300 Transmission cradle 04 01 91 used to support trans. E39
83 30 0 491 781 245 360 Seal remover 04 02 97 A14 used to remove the shift shaft seal E34,E36
83 30 0 491 788 245 370 Seal installer 04 02 97 A14 used to install the shift shaft seal 528i,E39
83 30 0 491 789 245 490 Seal Guide 04 08 95 A14 protects shift shaft seal during instillation x E31,E34,E38
83 30 0 491 791 246 000 8 pin test cable 04 26 91 used to troubleshoot the 4HP22/24 transmissions x 4HP22/24
83 30 0 491 797 246 060 16 pin test cable 04 10 93 used with 88 88 6 611 459 to test trans. circuits E38
83 30 0 491 799 251 100 Spanner wrench 04 19 86 B17 used in removal of shift lever x S38
83 30 0 491 800 251 110 Spanner 04 16 90 B17 used to R and R shifter E31
83 30 0 491 810 261 020 transmission gauge 04 31 87 shelf used to align transmission x All
83 30 0 491 811 261 030 Gauge 04 08 84 used to align drive train x All
83 30 0 491 812 261 040 Wrench 04 08 84 A11 used to remove the sleeve on the driveshaft x All
83 30 0 491 814 261 060 46mm wrench 04 23 87 used to R&R propeller shaft nut E30
83 30 0 491 815 261 070 Puller plate 04 25 86 B17 used when removing driveshaft CV joint E32
83 30 0 491 816 261 080 Mandrel 04 16 90 C2 used to remove guide bearing form propeller shaft E31
83 30 0 491 819 271 000 Fixture 04 23 87 used to mount transfer case on stand E30
83 30 0 491 824 271 050 Oil seal puller 04 23 87 C2 used to remove oil seal from transfer case x 325IX,E30
83 30 0 491 825 271 080 Seal driver 04 23 87 C2 used to install oil seals into transfer case of front axle shaft to final drive x 325IX,E30
83 30 0 491 828 271 090 Seal driver 04 23 87 used to install seals into the transfer case/rear output shaft x E30
83 30 0 491 829 271 120 Sleeve 04 23 87 used with 88 88 6 231 300 to pull output shaft into rear transfer case E30
83 30 0 491 830 271 160 Bushing driver 04 23 87 used to install the busshing in the input shaft of the transfer case x E30
83 30 0 491 831 271 190 Installer 04 23 87 used to install trnsfer case mounts E30
83 30 0 491 868 311 050 Sleeve C2 used to remove rubber bushings from front struts x E24,E28,E32,E34
83 30 0 491 873 311 110 Puller C2 used to remove tie rod end x E23,E24,E28,E32,E34
83 30 0 491 874 311 120 Thrust block 04 25 86 B21/C21 used to remove rubber engine mount bushings x E32
83 30 0 491 875 311 400 Tension rod test gauge 04 17 97 A12 used to examine the tension rods for damage x M52,E39
83 30 0 491 878 311 430 Ball joint fork 04 21 94 A13 removes front ball joint x E36
83 30 0 491 881 311 440 Ball joint press 04 21 94 A12 used to replace ball joint x E36
83 30 0 491 895 312 070 Thrust sleeve 04 23 87 used with 88 88 6 312 090 to press out front wheel bearings x E30
83 30 0 491 896 312 080 Socket 46 mm A2 used to R and R front wheel bearing x E23,E24,E28,E34,E36
83 30 0 491 898 312 100 Puller B5 used to remove front wheel bearing unit x E24,E28,E30,,E31,E32,E34,E36
83 30 0 491 902 312 104 Plate 04 01 83 A17 used with 312 103 to remove front bearine assembly x E30
83 30 0 491 903 312 105 Puler plate 04 25 86 A17 used with 312 101/102/106 to pull off bearing unit. x E32
83 30 0 491 904 312 106 Thrust block 04 25 86 A17 used with 312 101/102/105 to pull off bearing unit. x E32
83 30 0 491 905 312 110 Installer A17 used to install front wheel bearing unit x E28,E36
83 30 0 491 909 312 120 Puller 04 01 83 B18 used to pull wheel bearing ass. x E30
83 30 0 491 913 312 130 Thrust bushing 04 01 83 A17 used with 88 88 6 312 130 to R and R wishbone mount x E30
83 30 0 491 917 312 140 Thrust rod remover 04 01 89 A17 used to remove thrust rod x E32,E34
83 30 0 491 918 312 150 Puller 04 01 83 B18 used to remove wshbone rubber bushing x E30
83 30 0 491 923 312 155 Fixture 04 23 87 used to hold the control arm when installing rubber mount E30, 325IX
83 30 0 491 924 312 160 Control arm remover 04 23 87 B18 used to remove the control arm from the spring strut x 325IX,E30
83 30 0 491 930 312 200 Special socket 04 18 94 B18 used to expand the front axle wheel carrier when installing strut x E38
83 30 0 491 931 312 210 Strut socket 04 18 94 B17 use to loosen upper strut mount on vehicles with EDC x E38
83 30 0 491 932 312 220 Axle support 04 18 94 A21 supports front axle when removing oil pan x E38
83 30 0 491 933 312 240 Ball joint remover 04 18 94 B21 used to remove control arm bushings x E38
83 30 0 491 939 312 260 Bushing press 04 18 94 B21 used to press (in and out) control arm bushings x E38
83 30 0 491 942 312 270 Press 04 02 96 C14 used to R and R the tie rod bushing E39
83 30 0 491 946 313 010 Ride height measurment tool 04 07 96 C5 use to measure ride height x Z3
83 30 0 491 955 313 125 Spring clamping jaws 04 20 96 use in conjunction with 88 88 6 313 120 to compress springs x E38
83 30 0 491 961 313 150 Wrench 8 used to R and R strut nut x E21,E23,E24,E28,E30,E32, E34
83 30 0 491 962 313 160 Wrench A2 used to R and R strut nut x E12,E28
83 30 0 491 963 313 170 Wrench C4 used to R and R strut nut x E21,E28,E30,E32,E34,E36
83 30 0 491 964 313 180 Wrench C4 used to R and R strut nut x E30
83 30 0 491 965 313 190 Wrench C5 used to R and R strut nut x E30
83 30 0 491 967 313 210 Strut Socket 04 14 92 C5 used to R and the upper strut bolt - 22mm x All
83 30 0 491 969 315 000 Fixture 04 23 87 for mounting front axle final drive on stand E30
83 30 0 491 970 315 010 Puller/adapter 04 23 87 used to press off the output shaft on the front axle drive x E30
83 30 0 491 973 315 020 Seal driver 04 23 87 used to install oil seal onto the input shaft of the front axle final drive x E30
83 30 0 491 974 315 030 Seal driver 04 23 87 used to install output shaft seal on front axle drive x E30
83 30 0 491 975 315 040 Washer 04 23 87 used to preload shaft gears in final drive E30
83 30 0 491 976 315 050 Thrust sleeve 04 23 87 used to install roller bearing in differential case E30
83 30 0 491 977 315 060 Shaft adaptor 04 23 87 used with 88 88 6 002 000 to turn front axle when checking torque E30
83 30 0 491 978 315 070 Measuring tool 04 23 87 Used to check front axle drive pinion distance E30
83 30 0 491 981 315 080 Gauge disc 04 23 87 used with 88 88 6 002 510 to check front axle drive E30
83 30 0 491 982 315 090 Puller 04 23 87 used to remove tappered bearings in front axle drive E30
83 30 0 491 983 315 100 Installer 04 23 87 used to install outer race in bearing E30
83 30 0 491 984 315 110 Output Shaft Remover 04 51 02 Used to R x E53
83 30 0 491 988 321 050 pressing tool 04 06 82 used to insert rubber bushing in steering arm guide x e28 e24 e23
83 30 0 491 992 321 090 Securing ring press 04 01 96 C5 used to install steering wheel column securing ring x E36, E32, E34,E31,E38
83 30 0 491 993 321 100 Steering support Used to support the rack and pinion steering during R&R. E30
83 30 0 492 002 321 190 Ball joint press 04 18 94 C5 used to remove tie rod ball joints x E38
83 30 0 492 013 322 000 Puller C5 used to remove pitman arm x All
83 30 0 492 023 322 040 Puller A8 used to remove tie rod ends x E24,E28,E34
83 30 0 492 024 322 050 Puller A8 used to remove outside tie rod x E21,E23,E28,E31,E32,E34
83 30 0 492 025 322 070 Puller A8 used to remove center tie rod x E12,E30,E36
83 30 0 492 027 322 100 Wrench 27mm A8 used to R and R left tie rod x E21,E30
83 30 0 492 028 322 110 Wrech 32 mm A8 used to R and R right tie rod x E21,E30
83 30 0 492 029 322 120 Gauge 04 25 86 B8 used to adjust the steering drop arm on the vibration damper x E32
83 30 0 492 036 322 140 Steering box gauge 04 18 94 B8 used to adjust the steering box arm x E38
83 30 0 492 042 323 020 Clamping pliers 04 25 94 used to perform repairs for recall 94V-151, New Cartool PN is 175 500. x E36
83 30 0 492 043 323 050 Assembly sleeves Used to mount the snap ring on the stering spindle. E12,32,3436,38,21,23,24,39,28,30,31
83 30 0 492 049 323 070 Mandrel and bushing 04 13 90 A8 used to mount spring circlip on stering spindle x E31
83 30 0 492 053 323 090 Ball joint press modification 04 32 03 This tool is used to remove the control arm. Refer to repair manual section 31 21 080. The modification pertains only to the lower section of the tool (PN 323 092). The opening is enlarged to 27.5mm and a chamfer (1) 1.5mm deep and at a 45 angle is applied E46
83 30 0 492 055 323 110 Ignition lock remover 04 18 94 A8 releases ignition lock tumbler x E38, All
83 30 0 492 056 323 120 E8 torx socket 04 01 83 A19 used to tighten bolt on steering x E30
83 30 0 492 057 324 000 Gauge A11 used to test pressure on steering pump x All
83 30 0 492 062 324 005 Presure adapter 04 02 86 B9 used to attach to power steering to test pressures x All
83 30 0 492 063 324 006 Pressure adapter 04 02 86 B13 used to attach to power steering to test pressures x All
83 30 0 492 064 324 007 Adapter 04 25 86 B14 used with 88 88 6 324 000 to check pressuer in regulator x E32
83 30 0 492 065 324 008 Pressure adapter 04 25 86 C5 used with 88 88 6 324 000 to check power steering pressure x E32
83 30 0 492 066 324 030 clamping fixture 04 06 82 used to check the play in the steering gear x e28
83 30 0 492 069 324 060 Clamp fixture 04 25 86 C5 used to hold the steering drop arm when checking for mechanical wear in thepower steering x E32
83 30 0 492 073 331 010 Holder C16 used to hold rear axle x E28,E30,E32,E34
83 30 0 492 074 331 020 Installer B15 used to install tapered roller bearings x E28
83 30 0 492 075 331 030 Mounting bracket 04 14 88 used to mount rear diff to stand E32
83 30 0 492 083 331 150 Puller B7 used to remove front input flange x All
83 30 0 492 086 331 190 Drift B7 used to install output flange oil seals x E23,E24,E28,E34
83 30 0 492 087 331 200 Drift B7 used to install output flange oil seals on 8 bolt differentials x E23,E24,E32,E34
83 30 0 492 090 331 230 Drift A13 used to install output flange oil seals on 6 bolt differentials x E23,E28,E30,E32
83 30 0 492 093 331 260 Drift 04 01 83 B16 used to install final drive shaft sealing ring x E30
83 30 0 492 096 331 300 Puller A2 used to remove roller bearings in rear diff. x All
83 30 0 492 108 331 312 Mandrel 04 27 94 A2 used with 88 88 6 007 500 to remove output flange inner ring. x E36 Compact
83 30 0 492 110 331 340 Installer A2 used to install drive pinion x E23,E24,E28,E32,E34,E38,E39
83 30 0 492 121 331 360 Puller A2 used to R and R outer race in rear diff. x E21, E23, E24,E28,E30,E32,E34
83 30 0 492 163 332 100 Clamp 04 01 83 A3/B3 used to hold output shaft when removing bearing x E30
83 30 0 492 169 332 110 Puller 04 01 83 A21 used to remove half shaft in final drive. This tool is replaced by 332 200. 332 111 - 332 203 332 114 - 332 204 332 115 - 332 208 332 116 - 332 201 332 117 - 332 207 332 118 - 332 205 332 119 - 332 206 x E30
83 30 0 492 177 332 118 Threaded spindle 04 13 90 B13 used with 88 88 6 332 110 to install output shaft into drive flange x E31
83 30 0 492 178 332 119 Spindle 04 07 91 A10 used with 88 88 6 332 110 to draw the output shaft into the drive flange x E36
83 30 0 492 179 332 120 Puller 04 01 83 B12 used to remove final drive cover bushing x E30
83 30 0 492 180 332 121 Spindle 04 27 94 C6 Used with 88 88 6 332 120 to R and R final drive x E36 Compact
83 30 0 492 186 332 300 Spring tensioner 04 13 90 used to R&R the rear coil springs x E31
83 30 0 492 201 333 030 press adapter 04 09 90 used to remove rear trailing arm E32
83 30 0 492 210 333 060 Torque wrench adapter 04 02 90 C1/C2 used with torque wrench to set trailing arm x E34
83 30 0 492 215 333 100 Bushing tool A15 used to R and R rear axle rubber bushings x E23,E24,E31,E32,E34,E36,E39, E30
83 30 0 492 222 333 107 Spindle 04 23 87 used with 88 88 6 008 550and 88 88 6 333 111 to remove the rear axle rubber mounts x 325IX
83 30 0 492 223 333 110 Puller 04 01 83 C14 used with 008 550 to remove bushing in rear axle suframe x E30
83 30 0 492 227 333 115 Bushing adapter 04 23 87 B15 used with 88 88 6 333 112/103/104 to mount the rubber mounts into the rear axle carrier x 325IX
83 30 0 492 228 333 120 Extractor/pull in tool 04 25 86 A6 used on rubber bushing at side of rear axle subframe. See SIB for details x E32
83 30 0 492 232 333 140 Extractor/pull in tool 04 25 86 used on the rubber bushing in the rear axle sub frame. See SIB for details x E32
83 30 0 492 238 333 150 Press 04 13 90 used to press strut bushings E31
83 30 0 492 248 333 170 Press 04 13 90 used to press bushing in fron ttrailing arm E31
83 30 0 492 252 333 180 Press 04 13 90 used to press bushing from final drive support E31
83 30 0 492 260 333 200 Press 04 13 90 used to press bushings from guide arms E31
83 30 0 492 264 333 210 Press 04 13 90 used to press ball joints E31
83 30 0 492 269 333 220 Mandrel set 04 13 90 used to R&R rear subframe mounts x E31
83 30 0 492 276 333 240 Puller 04 13 90 used to re-move the inner bearing race from the drive flange x E31
83 30 0 492 287 333 260 Extractor set used to R&R whell bearing carrier x E38
83 30 0 492 289 333 262 Press housing 04 18 94 A4 Used to R and R wheel bearings. See SIB for additional parts x E38
83 30 0 492 293 333 266 Bearing press 04 18 94 B6/B7 removes wheel bearing . See SIB for additional parts x E38
83 30 0 492 294 333 267 Bearing press 04 18 94 A4 removes wheel bearing. See SIB for additional parts x E38
83 30 0 492 295 333 268 Bearing press 04 18 94 C7 used to replace wheel bearing. See SIB for additional parts x E38
83 30 0 492 296 333 270 Support frame 04 27 94 used to support the rear axle subframe. April 2008 - no longer available. See tool number 83 30 0 495 567. E36 Compact
83 30 0 492 302 333 290 Support jig 04 07 91 used to support the rear axle assembly E36
83 30 0 492 306 333 300 Support 04 18 91 used with 88 88 6 002 040 E31
83 30 0 492 310 333 310 Press 04 13 90 Used to press final drive bushings. Order PN 83 30 0 495 312 for Cartool PN 333 312 thrust piece. 1/08 - If the spindle or nut are damaged the entire tool must now be replaced. PN 333 312 is no longer available. E31
83 30 0 492 316 333 316 Puller 04 16 93 A10 used to pull bushing into rear subframe E31
83 30 0 492 317 333 320 Puller set 04 07 91 used to R&R rear axle rubber mounts x E36
83 30 0 492 322 333 330 Puller set 04 07 91 used to R&R upper trailing arm ball joint mount x E36
83 30 0 492 327 333 340 Puller disc 04 07 91 used to remove front trailing arm rubber mount x E36
83 30 0 492 328 333 350 Puller set 04 07 91 use to R&R traverse arm mounts x E36
83 30 0 492 332 333 354 Spacer 04 25 95 A4 used to install rubber bushing in control arm x E36,E38
83 30 0 492 333 333 360 Bushing press 04 07 91 used to R&R rear axle rubber mounts x E36
83 30 0 492 337 333 410 Spreader bar 04 29 92 used to spread the rear wheels to remove final drive E31
83 30 0 492 338 333 420 Final drive drift 04 19 94 A14/B14 used to replace the output shaft seal on the 6 bolt/188 final drive x E32,E34,E36
83 30 0 492 339 333 430 Input seal driver 04 27 94 A2 used with 88 88 6 005 500 to install final drive output shaft seals x E36 Compact
83 30 0 492 340 333 440 Final drive drift 04 19 94 C23 used to replace output shaft seal on 8 bolt/188 final drive x E32,E34,E36
83 30 0 492 341 333 450 Final drive drift 04 19 94 C23 used to replace output shaft seal on 8 bolt/210/215 drives x E32,E34,E36
83 30 0 492 342 333 460 Output seal driver 04 27 94 C13 used with 88 88 6 005 500 to install final drive output shaft seal x E36 Compact
83 30 0 492 343 333 470 Final drive drift 04 19 94 C13 installs seal on 6 bolt /188 final drive x E34,E32,E36
83 30 0 492 344 333 480 Input seal driver 04 27 94 C14 used with 88 88 6 005 500 to install input shaft seal on K final drive x E36 Compact
83 30 0 492 345 333 490 drift 04 19 94 used to seat the input flange plate on the 8 bolt 210 and 215 final drives x E36 e34 e32
83 30 0 492 346 334 000 Support used to support rear axle flange x E34
83 30 0 492 348 334 020 Support used to support wheel bearing when inserting axle shaft x E34
83 30 0 492 349 334 030 Puller used to R&R rear wheel bearing x E36
83 30 0 492 359 334 040 Puller 04 01 83 C13 used to R and R rear wheel bearing x E30
83 30 0 492 368 334 049 Guide sleeve 04 07 91 C13 used to draw in wheel bearing x E36
83 30 0 492 369 334 050 Drift 04 01 83 C13 used to install the keeper plate in the drive flange x E30
83 30 0 492 370 334 060 Drift C14 used to install locking plate on rear axle shaft x E23,E24,E28,E32,E34
83 30 0 492 371 334 070 Adapter C14 used to insert rear axle shaft x E28
83 30 0 492 372 334 080 Adapter C12 used with 231 300 to insert rear axle shaft x E23,E24,E28,E32,E34
83 30 0 492 373 334 090 Puller 04 06 86 B23 used to remove the rear wheel inner race x E30
83 30 0 492 397 334 140 Bushing press 04 18 94 B23 use to R and R rear axle carrier buishings with 90 88 6 334 150 x E38
83 30 0 492 405 334 148 Support feet 04 20 00 Shelf Used with 334 140 to remove rear rubber mounts. x E39
83 30 0 492 406 334 149 Support feet 04 20 00 Shelf Used with 334 140 to remove rear rubber mounts. x E39, E90
83 30 0 492 407 334 150 Bushing press 04 18 94 B10 used to R and R rear axle carrier bushings with 90 88 6 334 140 x E38
83 30 0 492 413 334 156 Spindle 04 20 00 Shelf Used with 334 150 & 334 140 to R&R the rear axle mounts x E39
83 30 0 492 414 334 157 Pressure plate 04 20 00 B19 Used with 334 150 x E39
83 30 0 492 415 334 160 Bushing press 04 18 94 B19 used to R and R the rear axle split bushing x E38
83 30 0 492 421 334 170 Bushing press 04 18 94 B19 used to R and R rear axle bushings x E38
83 30 0 492 426 334 180 Press 04 02 96 B19 used to R and R the final drive bushings E39
83 30 0 492 431 334 190 Ball joint press 04 18 94 B18 used to R and R the rear ball joint x E38
83 30 0 492 436 334 200 Flange remover 04 18 94 B18 used to remove the rear axle wheel bearing flange x E38
83 30 0 492 444 334 250 Drift 04 23 96 B19 used to install output flange seal on 220 drive x M62
83 30 0 492 447 334 240 Seal Press 04 25 95 B18 used to replace final drive output seal x E36, E38
83 30 0 492 448 334 250 Drift 04 23 96 used to install output flange seal on 220 drive x E39,E38
83 30 0 492 449 334 390 Support Stand 04 07 91 used to support final drive E36
83 30 0 492 450 341 000 Puller B19 used to remove disc brake pads x All
83 30 0 492 452 341 020 Socket 7mm C17 used to remove front brake calipers x E24,E28,E32,E34
83 30 0 492 453 341 030 Wrench C17 used to adjust handbrake cable x E23,E36,E39,Z3
83 30 0 492 456 341 060 Pistone pliers Used to turn the brake piston in fixed calipers. E23,24,28,12,21
83 30 0 492 459 341 130 Dust cap 04 12 97 C17 used to press the caliper dust cap in place E39
83 30 0 492 465 341 060 Socket B17 used to R and R tapered bolts on brake calipers x All
83 30 0 492 467 341 260 Brake depth gauge 04 02 96 C17 Used to check the thickness of brake pads without removing wheels x E39
83 30 0 492 470 342 000 Brake wrench Used to adjust the brake shoe on rear drum brakes. E21,12
83 30 0 492 475 343 110 ASC T Wrench 04 08 91 C17 used to bleed ASC T system x E31,E32,E34,E36,E38,E39
83 30 0 492 481 343 160 Reducer C17 used to check cut in/out pressure of H31 brake system x All
83 30 0 492 485 343 200 Holder C17 used to hold H31 pressure regulator x All
83 30 0 492 487 343 220 Holding jaws 04 21 88 C17 used to hold H31 pressure accumulator x E31,E32
83 30 0 492 488 344 000 Allen wrench C17 used to R and R handbrake shoe x All
83 30 0 492 499 345 110 ABS/ASC Tester 04 33 92 used to diagnose ABS/ASC in cars without a data link. See SIB for details x E34
83 30 0 492 507 345 150 Adjusting gauge 04 23 87 used to adjust the ABS pichup sensor x E30
83 30 0 492 508 345 200 V adapter for ABS Mark IV G 04 10 95 used with 83 pin B.O.B. (90 88 6 614 420) to troubleshoot module x E36
83 30 0 492 509 350 010 Installation plate 04 09 95 C17 template for installation of PWG x E38 With M73
83 30 0 492 510 350 020 Installation plate 04 09 95 C17 template for PWG x E31
83 30 0 492 512 361 000 Runout gauge 04 08 88 shelf used to test tire/wheel runout x All
83 30 0 492 515 009 250 Torque wrench 04 12 96 used for low torque aplications such as chain tensioner adjustment x M52, All
83 30 0 492 516 361 020 Sidewall depressor 04 27 96 used to depress sidewalls of tires in order to place wheel weights All
83 30 0 492 525 009 280 Navigation calibrator 04 31 96 used with 88 88 6 009 200 to calibrate nav system E38
83 30 0 492 526 009 300 Grill removal tool 04 09 97 used to remove dash vents. x E38
83 30 0 492 545 372 020 Pressuer adapters 04 17 87 C17 used to test steering pump pressure x M70
83 30 0 492 562 415 030 Door gauges 04 28 91 C9 set of alignment gauges that helps with door alignment x E36
83 30 0 492 568 415 040 Door gauge 04 18 94 C9 used to measure the distance between the front door and the B-pillar x E38
83 30 0 492 569 416 100 Torx socket 04 14 92 C9 used to R and R engine hood mounting screws x E31
83 30 0 492 571 416 200 Alignment gauge 04 27 94 C9 used to align the rear hatch with the body x E36 Compact
83 30 0 492 581 511 040 Pin wrench 04 05 88 C9 used to align bumper x E34
83 30 0 492 584 511 061 Plier jaws 04 21 88 C9 used with 88 88 6 511 060 to remove rain gutters E30
83 30 0 492 586 511 080 Bumper socket 04 18 94 C9 Used to remove the rear bumper x E38
83 30 0 492 587 511 110 Rain gutter tool 04 05 90 C9 used to remove rain gutter without harming vehicle x E32,E34
83 30 0 492 588 511 130 Adjustment tool 04 07 96 C9 used to adjust the front and rear bumpers Z3
83 30 0 492 592 512 010 Pillar protector 04 12 97 C9 used to protect the A and B pillars during work All
83 30 0 492 596 512 070 Pin wrench 04 25 86 C9 used to R and door lock retaining nut x E32
83 30 0 492 597 512 080 Door contact gauge 04 22 91 C9 checks door contact switch. See SIB 51 07 91 for details x E36
83 30 0 492 601 512 120 Support 04 01 83 B9 used to hold engine hood when removing engine x E30
83 30 0 492 602 512 130 Rear window strut tool 04 17 92 A19 used to R and R the rear window strut x E34 Touring
83 30 0 492 604 512 150 Tailgat gas spring tool 04 05 99 A15 Used to remove the gas filled springs on the tailgate and rear window frame without damaging the paint. Refer to RM section 51 24 320. x E39 wagon
83 30 0 492 609 513 010 Windshield lifting device 04 01 99 This lifting device is used to R&R front, rear and side windows (touring and sport wagon). All
83 30 0 492 611 513 030 Windshield gauge 04 07 91 A15 used to posotion windshield (front and rear) during replacement x E36
83 30 0 492 628 513 058 filler strip tool 04 06 82 used to install windshield filler strip x e21
83 30 0 492 629 513 059 windshield tool 04 08 83 used to install the windshield filler strip x e23 e24
83 30 0 492 634 513 080 Window scale 04 01 91 A15 used to check the depth of window insertion x E31
83 30 0 492 641 513 110 Spanner 04 17 92 A15 used to R and R the rear window mounts x E34 Touring
83 30 0 492 642 513 120 Spanner 04 17 92 A15 used to R and R the threaded collar on the roof rack mounting x E34 Touring
83 30 0 492 643 513 140 T wrench 04 25 86 used to install door locking plate x e32
83 30 0 492 648 513 190 Door lock plate remover 04 23 94 A19 replaces 88 88 6 513 140. Releases locking plate x E36,E31,E32,E34, E31,E32,E34,E36
83 30 0 492 649 513 200 Door handle tool 04 18 94 B15/C15 used to remove the door handle and recess x E38
83 30 0 492 652 513 203 Locking release tool 04 05 97 A19 used to release the security locking plate on door handle. x E39
83 30 0 492 653 513 210 Windshield adj. gauge 04 04 97 A18 used to aid in the replacement of windshields. x E39
83 30 0 492 654 514 000 Headliner installation gauge 04 05 97 Not Stored on a board used to install headliner in cars with the Katherine antenna E38, E39
83 30 0 492 669 521 000 armrest socket 04 09 84 used to remove the slotted nut under the armrest e24 e23
83 30 0 492 670 521 100 Pivot pin installer 04 32 87 A18 used to install seat pivot pin x E24,E30,E32,E34
83 30 0 492 671 521 200 Seat rail clamp 04 03 92 521 200 used to adjust clearance on seat rails. See SIB 52 01 92 for details x E36
83 30 0 492 689 543 150 Locking pins 04 13 90 A18 used to lock gate in order to adjust sunroof x E31
83 30 0 492 690 543 160 2,5mm allen socket 04 12 93 A18 used to R and R headliner tension screw E36,cabrio
83 30 0 492 691 543 170 Sunroof positioning pins 04 04 97 A19 Used to possition sunroof to adjust cables. x E39, E38
83 30 0 492 692 543 410 Pin wrench 04 06 91 A18 used to R and R special screw on soft top mechanism - trailing lever x E30
83 30 0 492 693 543 420 Microswitch gauge 04 06 91 shelf used to adjust the electro-mechanical soft top switches x E30
83 30 0 492 703 611 110 2.5mm pin remover 04 06 87 used to remove 2.5 mm pins from the connectors x All
83 30 0 492 709 611 134 Pin removal tool Used to remove vehicle connector pins. Originally sent out with 88 88 6 611 130. x All
83 30 0 492 714 611 140 Pin removal kit 04 02 91 used to remove connector pins on E31 and newer vehicles. This set supersedes 611 130. Tool 611 140 is now superseded by 90 88 6 611 150. x E31 Newer
83 30 0 492 719 611 145 Connector release tool 04 10 96 used to remove connector pins x All 94 and On
83 30 0 492 721 611 151 release tool 04 10 96 used to release double spring flat contacts x all
83 30 0 492 723 611 153 Relay release tool 04 10 96 used to release relays x All 94 and On
83 30 0 492 733 611 230 Rear washer aligner 04 17 92 A18 used to hold the rear washer nozzle while aiming x E34 Touring
83 30 0 492 734 611 240 Rear washer spanner 04 17 92 C15 used to R and R the rear washer nozzle x E34 Touring
83 30 0 492 735 611 250 Relay pliers 04 07 85 C15 used to remove relays x All
83 30 0 492 736 611 300 Pliers 04 08 83 C16 removes outside mirror x E23,E28,E30
83 30 0 492 738 611 320 Rear wiper alignment gauge 04 05 99 C16 Used to align the rear window wiper drive axis. x E39 wagon
83 30 0 492 742 611 360 Socket release tool 04 12 97 C16 use to release elctrical socket holders All
83 30 0 492 802 612 070 Power supply cable 04 14 94 for safe testing of systems E36, E31
83 30 0 492 805 612 073 Test cable 04 18 95 used to carry out test on front seats when removed E38
83 30 0 492 806 612 300 Battery draw test cable 04 33 96 used to test battery draw without interrupting power supply. x All
83 30 0 492 811 613 010 Relay test kit 04 03 91 used to test relays in vehicle x E30 Newer
83 30 0 492 822 613 030 Yaw sensor cable 04 12 97 used with DSC III to test the yaw sensor E38
83 30 0 492 823 613 050 Relay test cable 04 15 85 used to activate fuel pump relay when using fuel injector cleaner x All
83 30 0 492 824 613 100 Release tool 04 07 96 C18 used to release headlight switch clips x Z3
83 30 0 492 825 613 190 EWSIII test cable 04 02 97 used to diagnose EWS III x E39
83 30 0 492 827 614 410 88 Pin break out box 04 14 90 used to troubleshoot systems. Cables for testing red 88 88 6 614 413 black 88 88 6 614 412 x M42 Newer
83 30 0 492 831 614 414 Diagnostic lead black 04 11 92 used to connect 88 88 6 614 410 to a meter (DIS etc) for testing x All
83 30 0 492 832 614 415 Diagnostic lead red 04 11 92 used to connect 88 88 6 614 410 to a meter (DIS etc) for testing x All
83 30 0 492 834 614 419 88 pin lock lever 04 11 92 used to replace damaged levers on 88 pin BOB All
83 30 0 492 835 614 420 83 Pin breakout box 04 18 94 Used to perform control module testing in various systems x E38
83 30 0 492 838 614 430 Multimeter extension 04 10 91 4.5mm multimeter test cable extension x E31 Newer
83 30 0 492 841 614 440 Microswitch test box 04 14 91 used to test switchs on EM soft top. x E30
83 30 0 492 842 614 450 20 pin test cable 04 06 91 used with 26 pin B.O.B. to test soft top micro switches x E30
83 30 0 492 843 614 460 E31 cable set 04 10 91 troubleshoot ELO connectors. See SIB for multiple cable P/Ns x E31 Newer
83 30 0 492 848 614 470 18 pin adapter cable 04 16 92 used with 88 88 6 611 459 to check ELO connectors. Non-coded configuration x All
83 30 0 492 849 614 480 12 pin test cable 04 13 92 used with 88 88 6 611 459 to check systems. Comes non-coded x All
83 30 0 492 851 614 490 2.5mm adapter cable 04 16 91 used with 88 88 6 611 459 to troubleshoot LKM wire harness. x E31
83 30 0 492 852 615 410 5 pin adapter cable 04 16 91 used to test the EKM 2.5mm 5 pin x E31
83 30 0 492 853 616 000 Wiper puller 04 18 94 A20 Used to remove the wiper arm from the drive spindle x E38
83 30 0 492 857 616 010 T80 torx wrench 04 13 90 A20 used to R and R drivers sidewindshield wiper arm x E31
83 30 0 492 860 616 020 V adapter cable 04 18 94 used to testing on D22.5 ELA connectors x E38
83 30 0 492 868 616 030 ELO V adapter cable 04 06 95 used to test ELO plugs. Set is made up from the following leads. 90 88 6 616 031 - 3 Pin, 90 88 6 616 032 - 4 Pin, 90 88 6 616 033 - 6 Pin Single Row, 90 88 6 616 034 - 6 Pin Double Row, 90 88 6 616 035 - 10 Pin, 90 88 6 616 039 - Instructions x E38
83 30 0 492 875 616 040 V adapter cable 04 18 94 used to perform testing on ELO ELA connectors x E38
83 30 0 492 882 616 070 ELA pin connector 04 02 95 1.5mm and 2.5mm contacts Electrical kit 4 x E38 Newer
83 30 0 492 890 616 080 Plug housing 04 02 95 ELO connectors, kit 4 x E38 Newer
83 30 0 492 893 616 090 Plug housing 04 02 95 ELO - ELA housings, kit 4 x E38 Newer
83 30 0 492 923 619 062 Repair set L 04 02 95 repairs ELO connectors x E38
83 30 0 492 924 619 063 Repair set M 04 02 95 repairs ELO connectors x E38
83 30 0 492 925 619 064 Repair set N 04 02 95 repairs ELO connectors x E38
83 30 0 493 015 621 110 Service interval reset tool 04 28 89 used to reset service interval. This unit supercedes 88 88 6 621 100. Use with 88 88 6 612 060 for 15 pin vehicles x All
83 30 0 493 020 621 140 20- 15 pin adapter 04 25 86 used to adapt 15 pin reset tool to 20 pin car x e32
83 30 0 493 029 621 210 Adapter cable ZAE/BAE 04 05 96 used with 88 88 6 621 270 to deploy airbag x All 94 and on
83 30 0 493 030 621 230 Airbag test leads 04 18 94 Used to perform testing on airbags x E38
83 30 0 493 036 621 250 Airbag plug 04 15 85 used to bridge pins 1 and 6 to troubleshoot airbag x E23
83 30 0 493 038 621 270 Ignition cable 04 15 85 used to ignite gas generators when scraping vehicle x E23
83 30 0 493 040 621 290 20 Pin SRS reset tool 04 22 89 reads out fault codes and resets memory of SRS x E30
83 30 0 493 049 630 010 Headlight wrench 04 13 90 A20 used to R and R headlights x E31
83 30 0 493 051 630 030 Headlamp gauge 04 25 91 A20 used to adjust concealed headlamps. See SIB 63 02 91 for details x E31
83 30 0 493 052 630 000 Alignment lids 04 13 90 shelf used to align the headlight covers x E31
83 30 0 493 055 630 110 Socket wrench 04 13 90 A20 used with 88 88 6 630 000 to adlust headlight covers x E31
83 30 0 493 058 630 113 Headlight adjuster 17MM 04 05 91 A20 used with 88 88 6 630 110 to adlust headlights x E31
83 30 0 493 059 630 400 Light check module test cable 04 15 96 used to locate faults in light check module x E39
83 30 0 493 060 631 000 Xenon light test cable 04 33 96 used to test Xenon lights x E39
83 30 0 493 063 641 110 Spanner socket 04 05 87 A20 used to remove nut on vane type A/C compressors x All So Earlyquipped
83 30 0 493 064 641 120 Release tool 04 15 94 used to disconnect the bowden cables from the heat/AC panel x E36
83 30 0 493 066 641 160 Test cable 04 13 94 used to test water valve operation while on road test E32 Newer
83 30 0 493 080 645 000 Puller A20 used to remove A/C pulley (swash plate) x All So Earlyquipped
83 30 0 493 081 645 010 Pulley puller 04 05 87 A20 used with 88 88 6 645 020 to remove clutch pulley on vane type compressors. x All So Earlyquipped
83 30 0 493 082 645 020 Clutch holder 04 05 87 A20/B20 used to hold the clutch on vane type A/C cnpressors. See SIB 64 01 87 for details. x All So Earlyquipped
83 30 0 493 083 645 030 Extractor A20/B20 used to remove thrust washer on A/C compressor (swash plate) x All So Earlyquipped
83 30 0 493 084 645 040 Installer B20 used to install housing on swash plate A/C compressor x All So Earlyquipped
83 30 0 493 085 645 060 installer B20 used to install springs on swash plate A/C compressor x All So Earlyquipped
83 30 0 493 088 645 090 A/C clamp 04 14 92 used to hold compressor to R&R clutch bolts x M70
83 30 0 493 093 652 000 Antenna wrench 04 06 87 B20 used to replace the power antenna mast x All So Equipped
83 30 0 493 094 652 100 Antenna pliers 04 22 87 B20 used to open power antenna housing. See SIB 65 11 87 for details x All
83 30 0 493 099 655 400 Release tool Used to release the Navigation unit. All with Navigation
83 30 0 493 100 657 100 ZAE/MRS Adapter cable 04 26 96 used inconjunction with 88 88 6 614 410 to diagnose ZAE/MRS system x E39
83 30 0 493 101 662 100 Tool Set Used to R&R the PDC sensors. All with PDC
83 30 0 493 108 170 007 Coolant tank cap test adapter 04 15 97 B20 170 007 replaces tool PN 88 88 6 170 006. 88 88 6 170 006 must be scrapped. x All
83 30 0 493 125 613 210 5 pin V adapter cable 04 05 98 usd to test seat heating switch x E46
83 30 0 493 126 613 220 8 pin V adapter cable 04 05 98 Used to test pass. power window and interior lights x E46
83 30 0 493 128 613 240 8 pin V adapter cable 04 05 98 Used to test power door locks x E46
83 30 0 493 129 110 235 Compression Tester 04 18 06 NA Used in conjunction with the GT1 and the 25 bar pressure sensor to test combustion cylinder compression. Refer to Repair Manual section 11 00 039. x E60 S85
83 30 0 493 130 116 150 Adjustment plate 04 06 98 B20 Used to adjust valve timing on double VANOS x E46
83 30 0 493 134 116 170 Sealing cap pliers 04 06 98 B20 remove VANOS sealing caps x E46
83 30 0 493 136 345 220 25 pin V adapter cable 04 05 98 used to test the ABS/DSC module x E46
83 30 0 493 137 345 230 43 pin V adapter cable 04 05 98 used to test the ABS/DSC module x E46
83 30 0 493 143 116 250 Backlash dial indicator 04 02 06 Used to measure the backlash on the balancing shafts. Refer to Repair Manual section 11 36 140.Precise measurement of the gear backlash is not possible without this tool. E60 M5
83 30 0 493 149 619 044 Cable crimping jaws 04 16 97 used in conjunction with 90 88 6 619 041 to crimp[ radio antenna connections. x All
83 30 0 493 151 651 100 Radio removal tool 04 15 97 used to remove the C33 radio E39
83 30 0 493 155 613 300 EWS ring remover 04 15 97 B20 used to remove the EWS ring antenna E39,E38,E39,E46
83 30 0 493 156 242 310 Reverse gear tool Used to remove the reverse gear piston A4S270R,310R
83 30 0 493 172 333 390 Rear diff. seal installer 04 04 98 B20 used to install input flange seal x E46
83 30 0 493 176 641 010 Heater control removers 04 04 98 used to unlock and remove heater controls x E46
83 30 0 493 179 323 040 Steering angle sensor guide 04 10 98 A19 used to guide the steering angle sensor onto the steering column x E46
83 30 0 493 181 333 400 Rear diff. seal installer 04 04 98 C19 used tinstall output flange seal x E46
83 30 0 493 182 611 260 30 pin V adapter cable 04 05 98 used to test 30 pin door harness x E46
83 30 0 493 183 651 150 HiFI test cable 04 01 00 used with B.O.B. 614 390 to troubleshoot the 42 pin hifi/top hifi amplifiers x e46
83 30 0 493 184 613 150 54 pin V adapter cable 04 05 98 Used to test the headlight switch x E46
83 30 0 493 185 611 270 24 pin V adapter cable 04 05 98 used to test 24 pin seat connector x E46
83 30 0 493 186 614 390 60 pin break out box 04 05 98 used to test 27 to 60 pin cables x E46
83 30 0 493 200 512 160 Engine hood brace 04 04 98 C19 used to support the engine hood during repairs x E46
83 30 0 493 221 212 160 SAC Clamping fixture 04 08 99 Used on all SAC self-adjusting clutches to reset the clutch for installation. this tool supercedes 90 88 6 212 150 on SIB 04 03 97. Refer to RM section 21 21 500. x All
83 30 0 493 222 616 200 Washer jet adjuster 04 04 99 C20 Used to adjust the headlight washer jets on the E39. Refer to RM section 61 67 040. E39
83 30 0 493 227 333 370 Rear axle bushing remover 04 04 98 C20 used to remove the rear axle bushing x E46
83 30 0 493 243 1116 180 Secondary sprocket fixture 04 06 98 C20 used to install the secondary sprockets x E46
83 30 0 493 249 116 380 Seal Tool 04 07 05 Used to install the valve stem seals on the N52. Refer to repair manual section 11 34 560. x N52
83 30 0 493 253 241 070 Seal Installer 04 27 00 C20 Used to insert the shaft seal in the oil pump. x E46
83 30 0 493 254 241 080 Seal puller 04 27 00 C20 Used with 005 010 to remove the input shaft seal. x E46
83 30 0 493 272 611 139 contact remover tool 04 06 00 used to remove 1.5mm contacts. Spare sleeve PN 90 88 6 611 154 x e46 e39 e38 Z3
83 30 0 493 283 113 244 Camshaft retainer 04 06 98 C20 used to secure camshaft with 113 240 x E46
83 30 0 493 284 312 156 Control arm brace 04 04 98 C21 used to install the front control arm in conjunction with 312 154/152 and 007 500 x E46
83 30 0 493 287 245 304 Transmission support plate 04 27 00 Shelf Used with 002 030 to support the A5S325Z transmission. E46
83 30 0 493 289 313 129 Spring retainer 04 04 98 used to compress the front springs in conjunction with 313 120 x E46
83 30 0 493 290 313 101 Spring retainer insert 04 04 98 used to protect spring when using 313 124 x E46, E65
83 30 0 493 306 323 030 Rear toe adjustment tool 04 04 98 C21 used to adjust rear toe x E46
83 30 0 493 308 612 074 Seat test cable 04 10 98 Used to test the electric seat adjustment functions with the seat removed. x E46
83 30 0 493 311 350 012 Kickdown gauge 04 13 98 C21 Used to set the kickdown switch on E38 750i vehicles from 8/97. Refer to RM section 35 41 480. x E38
83 30 0 493 321 135 250 Slide hammer 04 18 01 C21 Used with 541 210 to remove convertible top rivets. x E46
83 30 0 493 325 323 140 Camber Adjustment Tool 04 12 99 C21 Used to adjust camber during wheel alignment. Refer to repair manual section 32 00 610. Note- 323 141 replced by 323 145 and 323 142 replaced by 323 144. x E46
83 30 0 493 326 345 160 DSC3 socket 04 13 98 C12 Used to change the DSC3 pressure switch on M73 vehicles from 9/98 E38
83 30 0 493 337 002 080 Hand pump for lifetime oil 04 03 99 This pump was developed to aid in the filling of manual transmissions with Lifetime oil (MTF-LT1). A pump used with MTF-LT1 should not be used with any other type of oil. All
83 30 0 493 351 313 120 Spring compressor 04 08 90 used to remove coil springs. This tool has been replaced by 313 340. x All
83 30 0 493 363 116 420 VANOS socket 04 12 98 B22/C22 Used to R and R the VANOS solenoid valves. Refer to repair manual section 11 36 585 x E38/39
83 30 0 493 364 116 430 Assembly gasket 04 12 98 B22/C22 Used to press down on the upper timing case cover during assembly. Refer to RM section 11 14 080. x E38/39
83 30 0 493 365 116 440 Camshaft adjuster 04 12 98 B22 Used to check the camshaft stop adjustment. refer to RM section 11 36 610 x E38/39
83 30 0 493 366 513 130 Windshield mounting blocks 04 01 99 These special hard foam blocks are used during windshield replacement to properly tension the windshield while the glue dries. x All
83 30 0 493 370 119 110 Camshaft alignment tool 04 07 98 B22 Used to adjust intake camshaft. Refer also to SIB 11 07 98 x M44
83 30 0 493 386 117 120 Securing Pin 04 13 99 B22 Used to secure the camshaft in position when adjusting the valve timing. Refer to repair manual section 11 31 505. x E39 M5
83 30 0 493 389 116 450 Alignment tool 04 12 98 B22 Used to adjust the camshaft sprocket to the sensor gear. Refer to RM section 11 36 610. x E38/39
83 30 0 493 395 345 240 DSC III test cable 04 06 00 used with BOB 614 350 to troubleshoot ABS/DSC (42 pins) x all so equipped
83 30 0 493 396 614 350 23 pin test cable 04 06 00 used with BOB 611 459 to troubleshoot ELO 2.8mm and 5.2 mm contacts x e46 e39 e38 Z3
83 30 0 493 401 616 050 6 pin oval test cable 04 06 00 used to troubleshoot systems with amp-mqs (micro Quadlock System) connectors such as the rotation rate sensor x e46 e39 e38 Z3
83 30 0 493 415 657 110 MRS 3 Test Cable 04 11 99 Used in conjunction with 90 88 6 614 390 60 pin break out box ( 04 05 98) to troubleshoot the MRS 3 system.-Disconnect connector (1) from the MRS 3 control module-connect test cable to 60 pin B.O.B.-connect free end of test cable to the wiring harness x E46,E38,E39,Z3
83 30 0 493 416 334 400 Race removal kit 04 18 00 Shelf Used to remove rear hub bearing. All
83 30 0 493 421 230 200 41mm Socket 04 09 06 This extra long socket is used to R&R the 41mm nut on the SMG output flange. SMG transmission
83 30 0 493 422 230 210 Extractor Used to remove the selector shaft seal on the F transmission. E90
83 30 0 493 423 230 220 Impact bushing Used to install the selector shaft seal. E90
83 30 0 493 427 180 050 Catalytic converter wire remover 04 02 99 B22/C22 Used to remove the wires from the electrically heated catalytic converter. Refer to RM section 18 32 030. x E38 M73
83 30 0 493 428 117 140 Locking clips 04 13 99 B22/C22 Used to lock the secondary chain tensioner during R and R of the camshafts. Refer to repair manual section 11 31 011. x E39 M5
83 30 0 493 429 126 050 VANOS switching unit 04 15 99 Used with 90 88 6 126 410 (04 27 92) to R&R the VANOS unit. Refer to repair manual section 11 36 030 x E39 M5
83 30 0 493 430 117 130 VANOS Charging adapter 04 13 99 C21 Screws into the VANOS unit for R and R. Works with compressed air. Refer to repair manual section 11 36 030. x E39 M5
83 30 0 493 432 117 150 VANOS Spanner 04 13 99 C21 Used to adjust the splined hub of the VANOS gearbox to R and R the camshafts. Refer to repair manual section 11 31 011. x E39 M5
83 30 0 493 433 117 180 Piston Ring Pliers 04 13 99 C20 Used to insert the piston into the cylinder. Refer to repair manual section 11 25 530. x E39 M5
83 30 0 493 441 616 060 Wiper arm remover 04 16 00 C20 Used to remove the wiper arm. x All
83 30 0 493 442 110 270 Holding Lever 04 13 99 C21 Used to R and R the vibration dampener central bolts. Refer to repair manual section 11 23 010. x E39 M5
83 30 0 493 444 111 490 Pressure Testing Plates 04 13 99 B23/C23 Used in conjunction with 111 471 and 111 477 (90 88 6 111 470 04 22 92) to seal head openings for pressure testing. Refer to repair manual section 11 12 729. E39 M7
83 30 0 493 451 333 228 Bushing sleeve 04 02 01 C23 used to R and R the front bushings on the E46 and E36 series. They can be used in conjunction with special tool 90 88 6 333 280 (SIB 04 19 00) to replace the bushings without performing an alignment. Refer to repair manual section 33 32 042. x E46
83 30 0 493 452 333 227 Bushing sleeve 04 02 01 B24 Used to R and R the front bushings on the E46 and E36 series. They can be used in conjunction with special tool 90 88 6 333 280 (SIB 04 19 00) to replace the bushings without performing an alignment. Refer to repair manual section 33 32 042. x E46
83 30 0 493 453 130 150 Throttle Valve Synchronizer 04 13 99 shelf Attaches to the throttle body to synchronize the cylinder banks. Refer to repair manual section 13 54 010. Spacer washer PN- 90 88 6 130 154. x E39 M5
83 30 0 493 464 110 260 Engine Hoist Frame 04 13 99 shelf Used with an engine hoist to R E39 M6
83 30 0 493 517 323 080 Adjustment device 04 07 91 B24 used to adjust the rear wheel alignment x E36
83 30 0 493 519 161 157 tank ventilation leak coupler 04 02 00 used with 161 150 to seal the leak diagnosis pump dust filter during system test. Repair manual 16 00 100. Replaced by 161 176. x e46
83 30 0 493 539 315 130 oil seal tool 04 50 99 B24 used to install the frontt output shaft radial oil seal x e53
83 30 0 493 541 002 150 T50 torx socket 04 14 00 B24 Used to R and R the rear bumper. E46
83 30 0 493 542 115 180 TDC pin 04 50 00 used to secure the crankshaft in TDC possition for cylinder 1. Refer to repair manual 11 31 010 x e53
83 30 0 493 548 114 230 Pretension rod 04 50 00 used with 90 88 6 113 390 to adjust the timing chain tension. Refer to repair manual 11 31 010 x e53
83 30 0 493 549 271 360 Drift 04 12 03 Used in conjunction with 005 500 (Tool board #1) to install the input shaft seal on the E46 transfer case. Refer to repair manual section 27 21 010. x E46, E53
83 30 0 493 551 271 340 Seal Installation tool 04 12 03 Used to insert the front and rear differential shaft seals in the transfer case. Refer to repair manual section 27 21 020. x E46, E53
83 30 0 493 555 313 340 spring compressor tool 04 07 00 shelf this spring compressor tool was developed to handle the greater spring rates on MY 2000 vehicles. x all
83 30 0 493 564 611 149 Pin Removal Tool blade replacement 04 11 99 Replacement blades for pin removal tool 90 88 6 611 148. This tool will not be sent out via the Automatic Tool Shipment Program. Order replacement blades from the PDC. All
83 30 0 493 582 118 140 Assembly sleeve for Piston Used to install piston sizes 84, 84.08 and 84.25 mm. M54, 52, 52TU
83 30 0 493 583 118 150 Cylinder wall protector 04 15 03 Used in conjunction with 117 280 to insert the pistons while protecting the rings and cylinder wall. E66 N73
83 30 0 493 589 117 210 Seal Press 04 13 99 B24 Used to pull-in the radial oil seal for the lower timing case cover. Hand tighten bolts (1). x E39 M5
83 30 0 493 591 112 386 Thrust Plate 04 13 99 B24 Placed on the crankshaft in conjunction with 90 88 6 112 380 (04 22 92) to remove the radial oil seal from the lower timing case cover. Refer to repair manual section 11 14 141. x E39 M5
83 30 0 493 592 009 330 Adjustment Lever Set 04 10 99 B23 The set consists of an angle gauge for checking proper adjustment of the windshield wipers, and adjusting levers. Refer to repair manual section 61 61 010. x E47
83 30 0 493 596 312 263 Bushing sleeve 04 23 00 Shelf Tool replaces 312 262 part of 312 260. x E38,E39
83 30 0 493 597 221 010 transfer case bushing remover 04 50 99 A24/B24 used to R and R the transfer casr bushing. Refer to repair manual 22 32 001 x e53
83 30 0 493 624 416 120 Door Glass adjustment tool 04 10 99 B11/C11 Used to adjust door glass on the E46/2. This tool replaces tool 90 88 6 416 110 SIB 04 12 93. Additionally this tool can be used to tighten the hood bolts on the E31 as well as the rear power windows on the E31 and E36(convertible). Refer to repair manua x E46
83 30 0 493 626 631 010 Xenon test cable 04 07 01 C4 Used with 50-amp test cable to diagnose Zenon light problems. Refer to SIB for details. x E38,E39,E46
83 30 0 493 635 416 250 Adjustment Gauge 04 12 00 B9 Used to adjust rear lid x E46 sport wagon
83 30 0 493 640 161 022 fuel level sender spanner jaws 04 03 00 must be used with 88 88 6 161 020 to remove fuel sender spanner nut (steel). e38 e39 e46
83 30 0 493 644 312 264 bushing adapter 04 50 99 B5 used to R and R the lower control arm bushing. Refer to repair manual 31 12 138 x e53
83 30 0 493 645 334 158 mount remover 04 50 99 B6 used to remove the rear axle mounts. Refer to repair manula 33 33 001 x E53
83 30 0 493 646 334 159 mount installer 04 50 99 A7 used to install rear axle mounts. Refer to repair manual section 33 33 101 x e53
83 30 0 493 647 512 170 engine hood extension 04 50 99 A4 used to support the engine hood when in the work possition x e53
83 30 0 493 648 332 150 shaft remover 04 50 99 A19/B19/C19 used to R and R the wheel bearing and the half shaft on the front axle. epair manual section 31 21 090. x e53
83 30 0 493 649 323 150 Rear toe adjuster 04 51 00 B10 Used to adjust the rear toe. x E53
83 30 0 493 653 323 160 crowfoot wrench 04 50 00 used to R&R the tie rod from the steering rack. Refer to repair manual 32 11 100 x E53
83 30 0 493 654 246 070 GM5 diagnostic cable 04 21 00 C1 Used with 611 459 to test GM5 module. x E39,E46
83 30 0 493 681 641 020 grill remover 04 50 99 A3/B3 used to remove the fresh air grills x E53
83 30 0 493 685 230 250 Output flange nut wrench 04 52 00 B12 Used to R E53
83 30 0 493 687 009 340 switch block remover 04 50 99 B6/C6 used to R and R the window switch block and IHKA control panel. Refer to repair manual 64 11 331. One piece of this tool 009 341 is also used to adjust the gap on the X5 sunroof. x e53
83 30 0 493 688 333 280 Control arm alignment gauge 04 19 00 17 Used to align the rear lower control arm. E46,E36
83 30 0 493 689 611 330 Alignment Tool 04 10 00 A16 Used to align the rear wiper motor. x E46 sport wagon
83 30 0 493 694 333 230 bushing remover 04 50 99 B12 used to R and R the rear axle carrier bushings. Repair manual section 33 17 006 x e53
83 30 0 493 705 341 040 Allen wrench 04 13 90 C2 used to remove rear calliper - replaced by 90 88 6 341 080 x E31, all
83 30 0 493 709 114 240 OIl line disconnect tool 04 17 00 A23 Used to release the oil line. E52
83 30 0 493 710 118 190 Vibration damper brace 04 29 00 C1 Used with 118 200 to R x All
83 30 0 493 731 513 220 Window suction cup 04 11 01 Shelf Used to support window glass during R&R All
83 30 0 493 732 341 290 Ring spanner 04 52 00 A3 Used to R and R the pressure switch on the DSC unit. E53
83 30 0 493 739 114 380 Camshaft fixture 04 01 01 Shelf Used to depress the camshaft during bearing removal. x E46 M3
83 30 0 493 742 114 390 Oil pressure adapter 04 01 01 B21 x E46 M3
83 30 0 493 743 114 400 Magnetic holder 04 01 01 C2 Used to hold the valve shims. x E46 M3
83 30 0 493 748 119 120 Piston ring compressor 04 01 01 A1/B1/C1 Used to compress the piston rings. x E46 M3
83 30 0 493 749 119 130 Camshaft adjusting gauge 04 01 01 B1 Used to adjust camshaft. x E46 M3
83 30 0 493 750 119 140 Camshaft timing gauge 04 01 01 B1/C1 Used to check the timing of the camshaft. x E46 M3
83 30 0 493 751 119 150 Flex adapter 04 01 01 B1/C1 Used with 117 030 to remove the oxygen sensor. x E46 M3
83 30 0 493 754 113 163 Feeler gauge 04 01 01 A16 Used to check the valve clearance. x E46 M3
83 30 0 493 755 119 160 Clamping pliers 04 01 01 A14/B14 Used to R and R the clamps on the intake air manifold. Refer to repair manual section 11 61 050 x E46 M3
83 30 0 493 756 111 404 Sealing plates 04 01 01 Shelf Used to check the head for leaks. E46 M3
83 30 0 493 764 230 110 Transmission support fixture 04 03 01 Shelf Replaces p/n 230 040. Used to support S6S560G E39,E31
83 30 0 493 771 361 100 Wheel Clamp adapter 04 16 03 Used in conjunction with 81 10 0 021 292 to align the ACC sensor. Refer to SI for details. Replacement parts - Magnets 361 102 - 83 30 0 493 773, attachment stems 361 103 - 83 30 0 493 774 x E65/66
83 30 0 493 797 230 130 Transmission fixture 04 52 00 Shelf Use with 002 030 to support the transmission E53
83 30 0 493 801 230 230 Engine spacer 04 22 00 A7 Used to secure the engine when removing the transmission. x E46 Xi
83 30 0 493 802 118 200 Vibration damper holder 04 29 00 C19 Used with 118 190 to R x All
83 30 0 493 803 118 210 Vibration damper puller 04 29 00 C13/C14 Used to pull the vibration damper. x All
83 30 0 493 805 117 160 VANOS spanner wrench 04 01 01 A13 x E46 M3
83 30 0 493 806 221 017 Transfer case nut 04 09 03 Used in conjunction with 221 010 to remove the transfer case rubber mount. Refer to repair manual section 22 32 001. x E46/16
83 30 0 493 807 221 018 Rubber bushing remover 04 52 00 Shelf Replaces tool 221 011 part of tool 221 010 to remove the transfer case. x E53
83 30 0 493 808 221 019 Rubber bushing remover 04 52 00 C16 Replaces tool 221 012 part of tool 221 010 to remove the transfer case rubber bushing. x E53
83 30 0 493 814 614 300 DIS OBD cable 04 14 00 Shelf Diagnosis through the OBD port. x E46 and newer
83 30 0 493 815 311 170 Output shaft remover 04 22 00 B9 Used to remove the front output shaft. x E46 Xi
83 30 0 493 822 543 000 Pin wrench 04 25 00 A13 Used to adjust convertible top. x E46
83 30 0 493 824 334 261 Wheel bearing remover 04 52 00 B2 Used to remove the 49mm front wheel bearing. x E53
83 30 0 493 825 334 262 Bearing Installer 04 52 00 Used to install 49mm front wheel bearings. Refer to Repair Manual section 31 21 180. x E53
83 30 0 493 829 361 030 Wheel run out gauge 04 09 01 Shelf Used to measure wheel run out. Replaces 361 000. All
83 30 0 493 831 313 367 Protective insert 04 11 00 Shelf Used with 313 252 to protect spring x E52
83 30 0 493 832 611 148 Pin Removal Tool 04 11 99 Used to remove the pins from SLK connectors. x ALL
83 30 0 493 833 361 040 Wheel weight scraper 04 08 01 A12 Used to safely scrap the weights from vehicle wheels. All
83 30 0 493 837 138 030 6 pin test cable 04 25 01 C1 Used to test the EDK throttle valve. x Z3,E39,E46,E53
83 30 0 493 838 119 170 VANOS spacer 04 01 01 A12 Used to set up the VANOS unit. x E46 M3
83 30 0 493 839 212 170 SAC clamping fixture 04 14 01 B4 Refer to important information on SIB 04 14 01. x All
83 30 0 493 840 212 180 SAC Centering Ring 04 14 01 B4 Used in combination with 212 170 to ensure that the clutch is properly centered. This tool is applicable foe all SAC equiped vehicles. x ALL with SAC
83 30 0 493 843 110 280 Brace 04 01 01 B2 Used to hold the vibration damper to R x E46 M3
83 30 0 493 847 117 240 Seal installer 04 28 01 A10 Used to replace the crank seal. x E46 M3
83 30 0 493 852 612 090 Seat adapter cable 04 12 01 Used to test seat motors. x E52
83 30 0 493 854 630 410 LCM Test Cable 04 03 06 Used in conjunction with 614 390 to preform functional checks of th elight check module. x E38, 39, 46, 90
83 30 0 493 855 611 180 Pin removal tool 04 20 01 Shelf Used to remove the load carring terminals found in the fuse box. x All
83 30 0 493 863 334 410 Rear differential support 04 17 01 Shelf Used to support the final drive. All
83 30 0 493 881 119 180 Seal Installer 04 01 06 Used to pull the rear crankshaft seal into position. Refer to Replacing crankshaft radial sealing ring in the repair manual. Cartool PN 119 180. x N52
83 30 0 493 882 119 190 Plug mandrel Used to lock the flywheel in the TDC position. N62
83 30 0 493 893 641 450 AC sprayer 04 03 02 Shelf Used to remove the odor from AC systems. Refer to SI for details and 64 08 91. Used with 99 00 0 002 719. x All
83 30 0 493 902 121 120 Release lever 04 01 01 B13 Used to release the connector strip on the fuel injectors. x E46 M3
83 30 0 493 903 341 091 Brake caliper brush 04 10 01 A22 Used to clean the brake calipers without damaging them. All
83 30 0 493 912 612 310 Closed circuit adapter 04 24 00 C4 Used with 612 300 to measure current draw. x All
83 30 0 493 915 127 300 9 Pin adapter cable 04 05 02 Used in conjunction with the DISplus to troubleshoot the Valvetronic position sensor. x E65
83 30 0 493 916 127 310 10 Pin test cable 04 05 02 Used in conjunction with the DISplus and BOB 611 459 to trouble shoot the Valvetronic Control Module. x E65
83 30 0 493 920 230 240 Drift pin remover Used to remove the transmission gearshift actuator. x E46 with S54
83 30 0 493 922 119 400 Engine stand support 04 09 02 Shelf Used to mount the engine on the engine stand. E65 N62
83 30 0 493 923 119 410 Seal extractor 04 06 02 C4 Used to remove the front crank seal. x E65
83 30 0 493 924 119 420 Seal installer 04 06 02 C17 Used to install the front crank seal. x E65
83 30 0 493 926 119 450 Brace 04 06 02 B20 Used to hold the crankshaft to R x E65
83 30 0 493 927 119 460 Gauge set 04 31 01 Shelf Used to hold the camshaft at top dead center. x E65
83 30 0 493 929 119 480 Torsion lever 04 06 02 C7 Used to remove Valvetronic torsion spring during R x E65
83 30 0 493 930 119 490 Protective sleeves 04 06 02 B23 Used to protect the camshaft from damage x E65
83 30 0 493 933 119 200 Seal Puller 04 26 05 Used to remove the rear radial oil seal from the N52 engine. Refer to Replacing crankshaft radial sealing ring¿ in the repair manual. x N52
83 30 0 493 934 119 220 Seal remover 04 01 06 Used to remove the front crankshaft seal. Refer to Replacing crankshaft radial sealing ring front¿ in the repair manual. Cartool PN 119 220. x N52
83 30 0 493 935 119 230 Seal Installer 04 01 06 Used to install the front crankshaft seal. Refer to Replacing crankshaft radial sealing ring front¿ in the repair manual. Cartool PN 119 230. x N52
Добавлено через минуту:
83 30 0 493 936 119 240 Oil Filter Cap Wrench 04 17 05 Used to remove the oil filter cap on all N52 engines. Must be ordered from the local PDC. N52
83 30 0 493 938 119 260 Flywheel Lock 04 15 02 Used to lock the flywheel for removal and installation. Refer to repair manual for details. x E65/66
83 30 0 493 940 119 280 Crankshaft Holder 04 26 05 Used to R&R the crankshaft central bolt. Refer to Replacing timing Chain¿ in the repair manual. x N52
83 30 0 493 945 612 190 20 Pin test cable 04 08 02 C4 Used in conjunction with BOB 611 459 to test the seat control module. x E65
83 30 0 493 946 612 180 8 pin test cable 04 30 01 C4 Used in conjunction with the DISplus to adapt to the 8 pin seat module. x E65
83 30 0 493 947 612 170 5 pin adapter cable 04 30 01 C4 Used in conjunction with the DISplus to adapt to the 5 pin seat module. x E65
83 30 0 493 948 612 160 4 Pin test cable 04 30 01 C4 Used in conjunction with DISplus to adapt to the seat module. x E65
83 30 0 493 950 612 150 76 pin test cable 04 08 02 C4 Used in conjunction with BOB 611 380 to test the Lamp Module. x E65
83 30 0 493 951 612 140 9 Pin adapter cable 04 15 02 Used with DISplus/GT1 MFK cables to adapt the 9 pin power window motor for testing. x E65/66
83 30 0 493 952 631 030 16 Pin test cable 04 08 02 C4 Used in conjunction with BOB 611 459 to test the trailer module. x E65
83 30 0 493 953 612 130 10 Pin test cable 04 30 01 C4 Used to adapt the windscreen motor connector (WIM) for testing. x E65
83 30 0 493 954 612 120 16 pin test cable 04 08 02 C4 Used in conjunction with BOB611 459 to test the door module - TM. x E65
83 30 0 493 955 612 110 21 pin test cable 04 08 02 C4 Used in conjunction with BOB 611 459 to test the door components. x E65
83 30 0 493 956 372 040 12 pin adapter cable 04 30 01 C4 Used in conjunction with the DIS[plusto adapt to the Dynamic Drive System ARS. x E65
83 30 0 493 958 324 250 8 pin adapter cable 04 30 01 C5 Used in conjunction with DISplus to test the 8 pin steering column module. x E65
83 30 0 493 961 651 110 Wide screen monitor tool 04 33 01 Used to remove the wide screen board monitor. Refer to repair manual section 65 52 013. x E46 from 9/01
83 30 0 493 962 614 380 Break out box 04 01 02 Shelf Used to troubleshoot control modules. x E65
83 30 0 493 967 334 205 Thrust rod remover 04 50 02 Used to remove the thrust rods. x E53
83 30 0 493 971 119 340 Chain Tensioner 04 01 06 Used to set the timing chain tension while adjusting the valve timing. Refer to Removing and Installing intake and exhaust camshaft adjustment unit¿ in the repair manual. Cartool PN 119 340. x N52
83 30 0 493 973 119 360 Mandrel 04 01 06 Used to install the basket sealer valve for the crankcase. x N52, S85, N52
83 30 0 494 017 170 008 Radiator cap test hose 04 22 01 C7 Used with 170 000 to test the radiator cap function. x All
83 30 0 494 018 361 080 M-mobility spanner 04 19 01 C6 Used to torque the lid on the M-mobility unit. x All with M-mobility
83 30 0 494 019 541 210 Rivet remover 04 18 01 19 DP9 Used with 1135 250 to remove convertible top rivets. x E46
83 30 0 494 046 334 210 Rubber mount remover jaws Used in conjunction with 90 88 6 334 140 (E38) to remove the rear axle rubber mounts. Refer to repair manual section 33 33 101. E46 sport wagon
83 30 0 494 048 334 280 Bushing extraction tool 04 31 01 A7 Used to R x E65
83 30 0 494 057 346 320 Lever 04 06 02 C12 Used to depress the brake caliper piston on the front axle. x E65
83 30 0 494 058 321 030 Line lever 04 06 02 A12 Used to disconnect the hydraulic lines from the steering gear. x E65
83 30 0 494 062 245 306 Transmission support 04 31 01 Shelf Used with 002 030 to support the trans. during R&R x E65
83 30 0 494 128 361 460 32 pin test vcable 04 30 01 C4 Used in conjunction with BOB 614 390 to adapt to the 32 pin Tire pressure control RDC. x E65
83 30 0 494 131 613 160 54 Pin Adapter Cable 04 18 02 Used in conjunction with break out box 90 88 6 614 390 (SI B04 05 98) to adapt to the 54 pin Dynamic Drive system. Follow the instructions in the DISplus test plan. x E65
83 30 0 494 137 246 080 16 Pin Adapter cable 04 30 01 Used in conjunction with BOB 611 459 to test the auto trans. x E65
83 30 0 494 138 170 030 Oil cooler pliers 04 06 02 C11 Used to release the trans. oil cooler lines. x E65
83 30 0 494 141 241 350 Piston cover remover 04 21 02 Used to remove the piston sealing cover on the THMR1 transmission. Refer to repair manual section 24 00 x E36 E39
83 30 0 494 146 127 420 DME test cable 04 15 05 Used in conjunction with Break Out Box 90 88 6 614 380 (SI B04 01 02) to diagnose the MSV70 DME.1.Test cable2.Plates for BOB 614 380 - allow the BOB to be customized for the 2nd DME plug pin assignment. x E90
83 30 0 494 149 119 430 Pressure fixture 04 09 02 Shelf Used to check the N62 head for cracks. E65 N62
83 30 0 494 151 161 060 Fuel line plug 04 10 02 C24 Used to plug fuel line when fuel tank is removed. x E65
83 30 0 494 152 321 260 Crimp clamp pliers 04 15 01 Used to remove and install crimp clamps on BMW vehicles. The pliers have a side cutter that allows you to cut from 2 directions. Refer to repair manual section 32 11. All
83 30 0 494 155 372 050 10 pin adapter cable 04 30 01 C4 Used in conjunction with the DISplus to adapt to the 10 pin electronic damping control module - EDK. x E65
83 30 0 494 156 611 190 Ribbon Cable Pliers 04 10 03 Used to repair vehicle ribbon cables. Insert ribbon cable into housing (1) and lock with handle (2). x E65/66
83 30 0 494 157 614 310 16 Pin test cable 04 08 02 C4 Used in conjunction with BOB 611 459 to test the controller. x E65
83 30 0 494 158 614 320 Crimping set 04 31 01 Shelf Used to repair the fiber optic cable. x E65
83 30 0 494 165 612 200 8 pin extension cable 04 30 01 C4 Used to check the function of the electric seat removed from the vehicle. x E65
83 30 0 494 168 512 180 Hood locking bar 04 06 02 Used to hold the engine hood in the service position. x E65
83 30 0 494 171 334 227 Fixture set 04 09 02 Shelf Used to remove the rear axle carrier. E65
83 30 0 494 179 321 270 Plug set 04 06 02 Used to seal hydraulic lines during repairs. x E65
83 30 0 494 181 323 145 Camber adjustment tool 04 06 02 Used to adjust camber during alignment. 323 145 replaces tools 323 143, 323 141 and 323 142. Update 2/2006 - replace spindle # 323 144 with 323 146. Refer to SI B04 05 06. x E65/53
83 30 0 494 182 323 170 Airbag remover 04 06 02 Used to remove the steering wheel airbag. x E65
83 30 0 494 183 321 020 Tool set 04 06 02 Used to replace the dirt seal and support ring on the hydraulic steering lines. x E65
83 30 0 494 187 313 030 Extraction tool 04 31 01 Used to R and R the rubber bushings in the trailing arm. This tool was replaced in January of 2003. The new tool that replaces it has "N 06/2" stamped next to the Part number. If your tool does not have this replace it and discard the old tool. x E65
83 30 0 494 190 641 030 Release hook 04 06 02 Used to remove the face vent grills. x E65
83 30 0 494 195 333 181 Bushing tool 04 16 01 used to remove the rubber bushing on the rear axle carrier for the E46 M3. The tool, originally sent out with 88 88 6 333 180 (SIB 04 13 90) can be modified to work on the M3 or purchased new. To purchase new, order PN 90 88 6 333 181 from the PDC. To modify the existing tool refer to illustration R330341. E46 M3
83 30 0 494 196 121 310 MKA Multi-channel adapter 04 32 01 Used in conjunction with the DISplus and MFK2 cables to perform automatic engine tests on N62 engines and newer. May 2008 - this test box is no longer used. x E65/66
83 30 0 494 197 345 250 47 pin test cable 04 25 01 C1 Used with BOB 614 412 & 413 for trouble shooting x Z3,E46
83 30 0 494 199 242 370 Seal installer 04 06 02 Used to install the output shaft seal to the proper depth. x E65
83 30 0 494 200 242 360 Seal installer 04 06 02 Used to install the torque converter shaft seal. x E65
83 30 0 494 201 242 350 Seal remover 04 31 01 Used to remove the trans. output flange seal. x E65
83 30 0 494 208 245 366 Seal installer 04 06 02 Used in conjuction with 245 360 to install the shift shaft seal. x E65
83 30 0 494 212 242 380 Socket 04 09 02 Used with 230 020 to R&R the nuton the trans. output flange. x E65
83 30 0 494 213 242 390 Protective cap 04 09 02 Used to seal the trans. connector during removal. E65
83 30 0 494 217 313 369 Protective inserts 04 06 02 Shelf Refer to SI for details. x E65
83 30 0 494 219 612 210 5 pin widow test cable 04 14 02 Used to test the window motors with the door panel removed. x E65/66
83 30 0 494 251 513 240 Window Adjutment Wrench Used to adjust retraction depth. Refer vto repair manual section 51 32 154. E88
83 30 0 494 280 212 200 Clutch centering pin 04 28 02 Used to center the clutch disc (1) during installation. x E85
83 30 0 494 308 110 150 Engine support Bracket 04 07 03 shelf Used to support the engine while mounted on engine stand PN 88 88 6 001 450 (B04 17 87). x N73
83 30 0 494 309 117 270 Pin spanner wrench 04 07 03 Used to R&R the variable valve gearing on the intermediate shaft. Refer to repair manual section 11 12 105. x N73
83 30 0 494 310 117 280 Piston ring pliers 04 18 03 Used in conjunction with 118 150 to insert the pistons while protecting the rings and cylinder wall. E66 N73
83 30 0 494 316 112 007 Thrust Bushing 04 07 03 Used in conjunction with 88 88 6 112 000 (tool board #2) to pull the chain sprocket from the crankshaft. Refer to repair manual section 11 31 052. x N73
83 30 0 494 317 119 445 Crankshaft shim 04 07 03 Used in conjunction with 90 88 6 113 460 (B04 28 92, tool board 15) and 90 88 6 119 450 (B04 06 02, tool board 18) to hold the crankshaft during R&R of the central bolt. Refer to repair manual section 11 23 031. x N73
83 30 0 494 318 119 476 Camshaft Securing Bracket 04 07 03 Used in conjunction with 90 88 6 119 470 (B04 06 02) to secure the intake camshaft while fitting the end bracket. Refer to repair manual section 11 37 012. x N73
83 30 0 494 321 621 340 Airbag Adapter Cable Set 04 05 03 This adapter cable set is used to troubleshoot airbag system problems. the set consists of: 621 341-side airbag, head airbag, rear belt. 621 342-front belt, safety battery terminal 621 343-driver x E65/66
83 30 0 494 325 512 190 Door Lock Tool 04 16 02 Must be used to pretension the door lock to the correct position for installation. Failure to use this tool may result in door leaks caused by an out of alignment door lock seal. Repair manual section 51 21 090. x E65
83 30 0 494 326 311 060 Ball Joint Tester 04 03 03 Shelf Used to test ball joints for wear. Refer to SI for details.Refer to SI 04 14 06 for E46 M3 adapter (PN 311 071). x E46/53
83 30 0 494 332 663 121 OPPS fibreoptic cable - long Used to diagnose the MOST bus All
83 30 0 494 334 663 123 OPPS fibreoptic cable - short Used to diagnose the MOST bus All
83 30 0 494 362 119 000 Cylinder head clamping fixture 04 21 03 Shelf This head clamping fixture is used in conjunction with engine stand 001 450 to safely hold the head for disassembly & assembly. It is designed to especially hold the new style N62 heads but will work on all other engines. Refer to reapir manual section 11 12 503. x All
83 30 0 494 363 513 250 Door Handle Release Tool 04 23 02 Used to remove the front and rear outside door handles without damage. 1. Release slide 2. Release hook Refer to repair manual section 51 21 170 x E65/66
83 30 0 494 383 127 050 Secondary voltage test cable 04 27 01 Used with DISplus to test secondary voltage on the S54 engine. x E46 M3
83 30 0 494 384 323 143 camber adjustment tool 04 50 99 used to adjust camber during wheel alignment. Refer to repair manual section 32 00 610. This tool is replaced by 323 145. x e53
83 30 0 494 385 324 011 Pressure adapters 04 21 01 Used with 324 012 x E38
83 30 0 494 386 324 012 Pressure adapters 04 21 01 Used with 324 012 x E38
83 30 0 494 397 313 358 Spring Retainer 04 05 05 Used with spring retainer PN 313 354 (SI B04 07 00) to properly tension the coils when removing the springs.Note: Carefully follow the tool use application in SI B04 07 00. x E90
83 30 0 494 401 543 200 Folding top support 04 31 02 Used to hold the folding top for fabric replacement while removed from the vehicle. Refer to repair manual section 54 34 101. x E85
83 30 0 494 410 233 150 Shaft seal tool set 04 24 02 Used to R and R the transmission input shaft seal. x E85
83 30 0 494 416 233 160 Shaft seal tool set 04 24 02 Used to R and R the transmission output shaft seal. x E85
83 30 0 494 417 170 100 Coolant system pressure tester 04 08 03 shelf Used to pressure test the engine coolant system for leaks. Refer to SI for details. x All
83 30 0 494 429 170 130 Coolant tester adapter set 04 08 03 shelf Used to adapt old pressure fittings (PN 88 88 6 170 000) to the new coolant pressure tester (90 88 6 170 100). Refer to SI for details, x All
83 30 0 494 436 212 220 Spline cleaner 04 28 02 Used to clean the grease off of the splined transmission input shaft. x E85
83 30 0 494 439 230 134 Transmission support 04 28 02 shelf Used in conjnction with 230 130 to support the transmission during R&R. E85
83 30 0 494 449 000 451 Support Feet 04 28 02 shelf Used in conjunction with engine support 000 200 to support the engine during oil pan removal. E85
83 30 0 494 450 513 260 Release slide 04 24 02 Used to release the door handle during R x E85
83 30 0 494 453 613 040 EKP Test Lead 04 14 03 Used to troubleshoot the Electric Fuel Pump (also applicable for the E46 SULEV). x E60
83 30 0 494 464 136 030 Fuel Pressure adapter The repair manual section 13 31 028 instructs the tech to use this tool to test fuel pressure on the N54. The repair manual is wrong. Use special tool 135 270 to test the fuel pressure. N54
83 30 0 494 467 541 220 Rivet pliers 04 23 03 Used to install plastic rivets on bumpers and exterior plastic trim panels. The rivets (available through Parts) range from 1.9 mm to 3.6 mm in diameter. E46
83 30 0 494 468 321 280 Hydraulic motor clamp 04 24 02 Used to hold the hydraulic motor on the valve housing assembly during installation. Refer to repair manual section 34 52 516. x E85
83 30 0 494 469 323 180 Clamp 04 24 02 Used to hold the steering gear in the center position during R x E85
83 30 0 494 474 512 195 Door lock jig 04 24 02 Used in conjunction with 512 190 (SI B04 16 02) to correctly pretension the door lock during assembly. Refer to repair manual section 51 21 090. x E85
83 30 0 494 482 114 223 Chain tension spindle 04 07 97 replaces spindle on tool 90 88 6 114 220. Refer to SIB 04 07 95 x M52,Z3
83 30 0 494 492 002 240 Plastic rivet pliers 04 23 03 Used to install plastic rivets on bumpers and exterior plastic trim panels. The rivets (available through Parts)range from 1.9 mm to 3.6 mm in diameter. E46/53
83 30 0 494 500 233 110 Drift 04 26 02 Used to install the shift pin sleeve and sealing cap on S5D280Z/310Z/320Z transmissions. x E36/39/46/53
83 30 0 494 501 161 170 Evap system tester 04 26 00 Shelf Used to test for leaks in the evaporative system. Order under new PN 83 30 0 494 501. PN 161 176 can be order under PN 83 30 0 495 345. x All
83 30 0 494 505 131 340 Fuel Injector remover 04 07 03 Used in conjunction with slide hammer PN 90 88 6 135 250 (B04 18 01, tool board 19) to remove fuel injectors. Refer to repair manual section 13 64 593. x N73
83 30 0 494 506 242 400 Seal Drift 04 14 03 Used to fit the radial oil seal on the torque converter for the 6HP19 (GA6 HP19Z) transmission. x E60
83 30 0 494 515 641 460 AC sprayer wand 04 07 04 Used in conjunction with AC disinfectant sprayer (SI B04 03 02) to clean and disinfect the AC system on vehicles that exhibit a musty odor. This PN is no longer to be used. Discard the tool and order PN 83 30 0 494 515. E65/66, E65/66
83 30 0 494 518 641 040 AC belt tool 04 25 04 Used to aid in the installation of the Air Conditioning belt on the N62. Refer to Repair manual section 11 28 050 for details. x E60,63,64,65 w/N62
83 30 0 494 529 131 140 Fuel injector installation fixture 04 06 03 shelf This tool must be used to properly install the fuel injectors. Refer to repair manual section 13 53 240. x E46 with M56
83 30 0 494 541 312 230 Strut Wrench 04 20 03 Used to open up the wheel carrier when removing the spring strut. Refer to repair manual section 31 31 000. x E65/66
83 30 0 494 542 321 300 Release Fork 04 20 03 Used to release the quick release couplings on the N73 steering box hydraulic lines. Refer to repair manual: -32 Overview of steering -9 power steering gear -R&R power steering gear -32 13 060 -32 13 x E65/66
83 30 0 494 543 233 200 Extractor 04 23 04 Used to remove the input shaft seal. Refer to repair manual section 23 12 510. x E46,53,60,83 w/GS6-53BZ
83 30 0 494 546 233 210 Extractor 04 23 04 Used to remove the output shaft seal. Refer to repair manual section 23 12 059. x E46,53,60,83 w/GS6-53BZ
83 30 0 494 584 330 170 ARS Gauge 04 14 03 Used to properly position the ARS (Active Roll Stabilization lines) at the rear axle. x E60
83 30 0 494 602 613 060 Power Window Test Lead 04 14 03 Used in conjunction with 612 071 (B04 11 92) to actuate the power windows with the battery removed. x E60
83 30 0 494 611 334 420 Support Adapters Used with support stand 002 030 to support rear differentials. All
83 30 0 494 612 612 220 DSC Test Lead 04 14 03 Used to troubleshoot the DSC-8 (Dynamic Stability Control) system. x E60
83 30 0 494 613 612 230 AFS Test Lead 04 14 03 Used to troubleshoot AFS (Active Front Steering) system. x E60
83 30 0 494 624 313 381 Top spring retainer 04 13 03 shelf Used in conjunction with 313 340 to R x E65/66
83 30 0 494 625 313 382 Bottom spring retainer 04 13 03 shelf Used in conjunction with 313 340 to R and R E65 (sportr suspension) springs. x E65/66
83 30 0 494 626 313 364 Spring Retainer Insert 04 13 03 shelf Used in conjunction with 313 381 to protect the spring. Always replace the insert if worn or damaged. x E65/66
83 30 0 494 627 520 070 Release Hook 04 14 03 Used to remove the head restraint guides. x E60
83 30 0 494 628 312 158 Base adapter 04 24 01 Used on E46 vehicles from 2/01 production. Refer to SIB for details. x E46
83 30 0 494 635 361 130 ACC Adjuster 04 20 03 This is an extra long T20 Torx used to adjust the ACC sensor (2) via the adjusting screws (3). Refer to repair manual section 66 31 001. x E65/E66
83 30 0 494 640 271 370 Drift 04 12 03 Used to install the output shaft seal (rear axle differential) on the E53 transfer case. Refer to repair manual section 27 21 020. x E46, E53
83 30 0 494 641 271 380 Seal Installer 04 13 04 Used to insert the rear differential output shaft seals. Refer to repair manual section 27 21 020. x E46 E53
83 30 0 494 642 170 113 Coolant System Adapters 04 14 03 Used in conjunction with coolant system test kit 170 100 to check for leaks. x E60
83 30 0 494 643 170 114 Coolant System Adapters 04 14 03 Used in conjunction with coolant system test kit 170 100 (SI B04 xx 03) to check for leaks. x E60
83 30 0 494 645 512 220 T25 Torx Driver 04 14 03 This extra long Torx driver is used to R&R the read door handles. x E60
83 30 0 494 649 212 230 Clutch centering tool 04 17 04 Used to align th eclutch (GS6-53BZ) during instalation. Refer to repair manual section 21 21 500. x E60 545
83 30 0 494 650 212 240 Grease Scraper tool Used to clean the grease from the input shaft on the GS6-53BZ transmission. E60 M5
83 30 0 494 651 233 220 Installer 04 23 04 Used to install the input shaft seal. Refer to repair manual section 23 12 510. x E46,53,60,83 w/GS6-53BZ
83 30 0 494 652 233 230 Installer 04 23 04 Used to install the output shaft seal. Refer to Repair Manual Section 23 12 059. x E46,53,60,83 w/GS6-53BZ
83 30 0 494 653 334 230 Rear Axle Carrier 04 14 03 shelf Used in conjunction with 002 030 E60
83 30 0 494 654 334 270 Bushing Tool 04 14 03 Used to R&R the rear axle carrier rubber mount. Tool 334 272 replaces a part of special tool 334 270 (83 30 0 494 654 SI B04 13 03). Remove and discard old bushing sleeve PN 334 272 (2) from special tool 334 270 ¿ Replace with new 334 272 x E60
83 30 0 494 655 324 150 AFS Gauge 04 14 03 Must be used during wheel alignment to fix the steering shaft in place. New barcket and fork sent out to fit new models. Refer to SI B 04 05 04. x E60
83 30 0 494 656 323 190 Camber Adjustment Tool 04 14 03 Used to adjust the front axle camber. x E60
83 30 0 494 660 110 170 Injector Ring Kit 04 19 03 Used to replace the Teflon sealing ring on the N73 fuel injectors. The Teflon sealing ring must be replaced every time the injector is removed and reinstalled. Refer to repair manual section 13 64 593 for detailed instructions. Bass cone cartool # 110 172 may be ordered from Parts under PN 83 30 0 494 662. x E66/N73
83 30 0 494 679 641 240 AC System Adapter 04 31 03 Used to adapt AC fill and testing devices to the vehicle pressure side due to the recessed fitting. x E60
83 30 0 494 696 610 052 Vehicle Key Memory OBD cable NLA Used with the vehicle key memory unit to program vehicles. Used in conjunction with 90 88 6 610 051 extension cable. This item is no longer used. All
83 30 0 494 711 334 272 Bushing Sleeve Tool 04 37 06 This tool replaces a part of special tool 334 270 (83 30 0 494 654 SI B04 14 03). Remove and discard old bushing sleeve PN 334 272 (2) from special tool 334 270 Replace with new 334 272 x E60, 61, 63, 64
83 30 0 494 721 334 310 Bushing fixture 04 19 05 Used to install the front bushing on the rear axle carrier. Refer to repair manual section 33 17 506. x E60
83 30 0 494 724 541 230 T10 Torx bit 04 22 03 Used to R&R the headliner without removing the sunroof lid. Must be used in conjunction with a 2-way bit ratchet such as a Blue-Point YA489 available on most Snap On trucks. Refer to repair manual section 51 44 011 x E60
83 30 0 494 729 610 060 Fiber optic protective cap 04 27 03 shelf Fiber optic cables are frequently detached from their connections during repairs or bodywork. It is essential to keep the light sensitive contact surfaces clean. Using tape on the surfaces will leave a residue, which will affect the function of the cable. The protective cap can be used on the cable and the equipment side.Ten pieces are delivered with each order. x E60/65/66/85
83 30 0 494 730 411 110 Febder adjusting wrench 04 10 04 Used to adjust the fit of the front fenders. Loosen bolt and adjust the spacer sleeve with the wrench. E63/64
83 30 0 494 733 411 120 Door Brake Ball Pliers 04 09 04 Used to remove without damaging the door brake ball end. Refer to repair manual section 51 21. E65/66
83 30 0 494 737 117 231 Seal Aligner 04 13 99 Used to install the radial oil shaft seal on the lower timing case cover without damage. Refer to repair manual section 11 14 141. x E39 M5
83 30 0 494 745 613 120 Switch adjustment tool 04 19 05 Used to adjust the gap between the switches and trim pieces on the drivers steering wheel airbag. Refer to repair manual section 61 31 220. x E60
83 30 0 494 754 331 110 Bushing Remover Kit 04 12 04 Shelf This bushing kit was developed to localize several frequently used bushing removal tools. Refer to the SI for details. All
83 30 0 494 758 230 135 Gearbox support Used to support G5S-53BZ SMG transmission. E46/85
83 30 0 494 760 513 290 Trunk lid wrench 04 31 03 Used to R&R the trunk lid tension spring. E60
83 30 0 494 762 212 050 Flywheel bearing tool set 04 08 04 Used to R&R the dual-mass flywheel roller bearing. Refer to repair manual section 11 22 513. E60, E63 with M54, N62
83 30 0 494 767 613 080 Transfer case test cable 04 28 03 Used to test the operation of the transfer case drive motor x E83
83 30 0 494 768 613 090 Transfer case test adapter 04 28 03 Used to test the operation of the transfer case control module x E83
83 30 0 494 769 613 130 Airbag adapter cable MRS4 04 28 03 Used in conjunction with 614 380 (SI B04 01 02) to test the operation of the airbag control module. x E83
83 30 0 494 776 271 390 Seal installer 04 28 03 Used to install the output shaft seal in the transmission. Refer to repair manual section 27 21 010. x E83
83 30 0 494 777 271 400 Seal Installer 04 28 03 Used to install the output shaft seal in the rear axle differential. Refer to repair manual section 27 21 020. x E83
83 30 0 494 778 271 410 Seal installer 04 28 03 Used to install the output shaft seal in the front axle differential. Refer to repair manual section 27 21 030. x E83
83 30 0 494 780 221 021 Bushing installer 04 28 03 Used in conjunction with 90 88 6 221 010 (SI B04 50 99) to insert the transfer case rubber mount. Refer to repair manual section 22 32 001. x E83
83 30 0 494 782 110 250 Engine support 04 28 03 Used to support the engine during gearbox R&R. Refer to repair manual section 23 00 019. x E83
83 30 0 494 786 621 120 Head-Up Display Adjustment Tool 04 04 04 The HUD is essential for proper operational examination as well as height adjustment of the HUD. Adjustment of the HUD must be carried out whenever the windscreen is replaced. The HUD is used in conjunction with a GT1 test module to project a test screen onto the HUD adjustment tool. 1.Projection gauge2.Adjusting tool x E63/64
83 30 0 494 787 510 040 Engine hood support 04 28 03 Used to hold the engine hood in full vertical position when working on the engine. Refer to repair manual section 51 00. x E83
83 30 0 494 794 135 460 Fuel adapter 04 31 03 Used to draw-off residual fuel in conjunction with a fuel-refilling device (not included). Refer to repair manual section 16 00 005. E60
83 30 0 494 797 332 160 Spacer Ring Used to remove and install front and rear wheel flange. Refer to repair manual section 33 41 151. E65/53/63/64/66/83
83 30 0 494 804 313 383 Spring holder 04 28 03 Used in conjunction with 313 340 (SI B04 07 00) and 313 382 (SI B04 13 03) to R&R the coil springs.Application note: Never use an air impact driver on the spring compressor as damage can result. Instead, use a hand ratchet or a geared electric drill with a low range such as the Hole Hawg (1675-6) Always use the BMW Spring Compressor in accordance with use and safety procedures as stated in the BMW repair instructions. Never try to use or repair a damaged tool. Refer to repair manual section 31 31 031. x E83
83 30 0 494 805 212 246 Ball joint press 04 01 04 The lower section of ball joint remover 90 88 6 312 240 (SI B04 18 94) is redesigned which prevents the stainless steel sliding ring on the control arm from being damaged when removed. Refer to repair manual section 31 21 090. This tool (312 246) is only for the E53. x E53
83 30 0 494 806 251 120 Spanner wrench 04 28 03 Used to remove and install the gear lever. Refer to repair manual section 25 16 056. New BMW number 83 30 0 494 806. x E83
83 30 0 494 807 312 300 Thrust rod remover 04 28 03 Used to press the trust rod out of the wheel carrier. Refer to repair manual section 31 21 151. Replaced by 312 310. x E83
83 30 0 494 818 245 307 Transmission Support Posts Used to R&R the automatic transmission 6HP26 all wheel version only. Used in combination with 245 301 and 245 306. E61/53 All wheel
83 30 0 494 819 130 130 Residual Fuel Collection Device 04 28 04 Used to safely collect the residual fuel in the N73 fuel lines in order to perform work on the fuel system. Refer to repair manual section 13 53 175. E66 N73
83 30 0 494 823 271 420 Seal installer 04 01 04 Used to install the front differential output shaft seal. Refer to repair manual section 27 21 030. x E53
83 30 0 494 826 311 140 Ball joint wrench 04 28 03 Used when removing & installing the ball joint of the front stabilizer. Wrench size is 16mm and 18mm. Refer to repair manual section 31 35 005. x E83
83 30 0 494 833 641 480 AC sprayer wand 04 29 05 Used in conjunction with AC disinfectant sprayer (SI B04 03 02) to clean and disinfect the AC system on vehicles that exhibit a musty odor. Refer to repair manual section RAE6064-6451001 E60, E61, E63, E64
83 30 0 494 837 314 050 Take up set Used in to support the front axle carrier during R&R. E70,93,81,83
83 30 0 494 840 641 490 AC Sprayer Wand 04 27 04 Used in conjunction with AC disinfectant sprayer (SI B04 03 02) to clean and disinfect the AC system on vehicles that exhibit a musty odor. Refer to repair instructions RAE8564-6451001 for application E85
83 30 0 494 867 324 154 Clamping bracket 04 05 04 The AFS gauge PN 90 88 6 324 150 previously distributed (SI B04 14 03) has been modified in order to fit the available tight space on the above models. See also 324 155. x E6063
83 30 0 494 868 324 155 Clamping fork 04 05 04 The AFS gauge PN 90 88 6 324 150 previously distributed (SI B04 14 03) has been modified in order to fit the available tight space on the above models. See also 324 154. x E60 E63
83 30 0 494 869 543 110 Lifting frame 04 18 04 The lifting frame used in conjunction with an engine crane, is used to remove and install the convertible top. The top weighs 154 pounds. Refer to repair manual section 54 34 101. E64
83 30 0 494 872 331 154 Adapter plate 04 23 04 Used to remove the output shaft flange. Refer to Repair Manual Section 23 12 059. x E46,53,60,83 w/GS6-53BZ
83 30 0 494 874 612 320 23 Pin adapter cable 04 12 05 Used only in conjunction with 612 330 and 614 390 or 614 380 to diagnose the junction box. x E90
83 30 0 494 875 612 330 47 Pin adapter cable 04 12 05 Used in conjunction with 612 320 and 614 390 or 614380 to diagnose the junction box. x E90
83 30 0 494 876 612 340 51 Pin adapter cable 04 12 05 Used in conjunction with 614 390 or 614 380 to diagnose the FRM. x E90
83 30 0 494 877 612 350 4 Pin adapter cable 04 12 05 Used to perform measurements on the roof function center FZD. This tool has a modification that allows it to be used on other modules. Refer to SI B04 17 07 for details. x E90
83 30 0 494 878 612 360 36 Pin adapter cable 04 12 05 Used in conjunction with 614 390 or 614 380 to diagnose the door contacts x E90
83 30 0 494 879 612 370 6 Pin adapter cable 04 12 05 Used to perform measurements on the steering column switch cluster SZL. x E90
83 30 0 494 880 612 380 12 Pin adapter cable 04 12 05 Used to perform measurements on the headlights. May also be used on E53 from 10/2003. x E90
83 30 0 494 881 612 390 3 Pin adapter cable 04 12 05 Used to perform measurements on the Park Distance Control PDC ultrasonic sensors. This cable needs to be converted in order for it to work on other connectors such as Vanos connectors. Refer to SI B04 10 07 for details. x E90
83 30 0 494 882 612 420 88 Pin adapter cable 04 12 05 Used to perform measurements on the Digital Motor Electronics DME in conjunction with 614 380.1.Adapter cable2.Cover plate for 614 380 (pin assignment) x E90
83 30 0 494 887 543 120 Lid support 04 18 04 Used to hold the convertible top in the service position so that adjustments or repair work may be performed. Refer to repair manual section 54 00. E64
83 30 0 494 888 234 020 Drift set for Locking Pins 04 22 04 Used to replace the 5th and reverse gear selector shaft bushings. Refer to service information B23 01 04 and to repair manual section 23 11 565 x E36, E39, E46, E53 with S5D 280Z/320Z Transmission
83 30 0 494 893 510 050 Tailgate support 04 13 05 Used on the left or right side of the tailgate for support when conducting repairs on the hydraulic piston and support system (service position). Refer to Repair Manual section 51 24 150. E61
83 30 0 494 898 543 140 Top support 04 18 04 Used in conjunction with 543 201 (SI B04 31 02) to prevent the top linkage from being damaged during work. Refer to repair manual section 54 34 101. E64
83 30 0 494 905 411 150 Door Hinge Bushing Tool 04 11 05 Used to replace the door hinge bushing. Refer to repair manual section 41 51 XX1 for details. E90
83 30 0 494 906 512 196 Protective side 04 15 04 Used with 90 88 6 512 197 to update tool 512 190. Refer to SI for complete information. x E60,63,64,65,66,85
83 30 0 494 925 314 060 Front Axle Support Set 04 05 05 Used with 002 030 and 002 040 to support the front axle during R&R. Refer to repair manual section 31 11 506. E90
83 30 0 494 926 334 430 Rear Axle Bushing Remover 04 05 05 Used to R&R the front rubber mounts of the rear axle carrier. Refer to repair manual section 33 33 101. For nut PN 334 435 order PN 83 30 0 495 034. x E90
83 30 0 494 927 334 440 Rear Axle Bushing Remover 04 05 05 Used in conjunction with 334 430 and 334 140 to R&R the rear rubber mount in the rear axle carrier. Refer to repair manual section 33 33 515. x E90
83 30 0 494 928 119 470 Valvetronic bridge support 04 06 02 Shelf Used to support the Valvetronic bridge during R&R x E65, E90
83 30 0 494 929 334 460 Rear Axle Bushing Remover King 04 05 05 Used to R&R the king pin control arm rubber mount in the rear axle carrier. Refer to repair manual section 33 32 195. Nut (6) can be ordered through the BMW Parts department under PN 83 30 0 494 982. Spibdle can be ordered under PN 83 30 0 494 981. x E90
83 30 0 494 930 334 470 Rear Axle Bushing Remover Trailing Arm 04 05 05 Used to R&R the semi-trailing arm rubber mount in the rear axle carrier and wheel carrier. Refer to repair manual section 33 32 031. x E90
83 30 0 494 931 334 480 Ball Joint Remover 04 05 05 Used to R&R the ball joint. Refer to repair manual section 33 32 125 x E90
83 30 0 494 934 335 020 Reversible Ratchet 04 05 05 The ratchet has a reversible internal hex drive WAF22. It can be utilized on the spring tensioner 335 010. Refer to repair manual section 33 53 000. E90
83 30 0 494 938 009 010 E18 Socket 04 07 05 Used to R&R the aluminum transmission bolts on the N52 engine. Refer to repair manual section 24 00 030. x N52
83 30 0 494 962 212 250 Clutch Tool Used to center the clutch on all vehicles with S5D-250G transmission. Refer to repair manual section 21 21 500. E46
83 30 0 494 968 652 010 Antenna Knife 04 04 05 Used on the above models to safely remove the roof-mounted antenna without doing damage to the paint. The knife may be converted for left handed use. Refer to repair manual section 65 20 035. Replacement Blade (3)90 88 6 652 013 E60, 65, 66
83 30 0 494 969 334 233 Rear Axle Carrier Support 04 26 04 Used in conjunction with support stand 002 030 to support the rear axle carrier during R&R. Refer to repair manual section 33 33 111. E60/63/64
83 30 0 494 991 334 490 Rear Axle Support Set 04 05 05 Used with 002 030 and 002 040 to support the rear axle during R&R. Refer to repair manual section 33 31 000 E90
83 30 0 494 999 114 250 Gauge 04 07 05 Used to properly place the oil spray nozzles. Refer to repair manual section 11 21 531. x N52
83 30 0 495 002 114 260 Oxygen sensor wrench 04 07 05 Used to R&R the oxygen sensor. Refer to repair manual section 11 78 510. x N52
83 30 0 495 003 114 270 R 04 07 05 Used to R&R the Valvetronic intermediate lever pressure springs. Refer to repair manual section 11 37 010. x N52
83 30 0 495 004 114 280 Camshaft Fixture 04 07 05 Used to fix the camshaft at TDC. Refer to repair manual section 11 31 505. x N52
83 30 0 495 008 114 290 Alignment Gauge 04 07 05 Used to R&R the camshaft sensor gear. Refer to repair manual section 11 31 505. x N52
83 30 0 495 009 114 490 R 04 07 05 Used to R&R the wrist pin retaining rings.1. Assembly bracket2. Removal pliers3. Assembly pliers4. Assembly driftRefer to repair manual section 11 25 530. 52
83 30 0 495 014 114 340 Pressure testing fixture 04 07 05 Used to pressure test the cylinder head for leaks. Refer to repair manual section 11 12 729. N52
83 30 0 495 018 114 350 Torque wrench 04 07 05 This torque wrench (1-5 Nm) is used to tighten the camshaft bearing strips. Refer to repair manual section 11 31 028. N52
83 30 0 495 019 114 360 R 04 07 05 Used to R&R the vacum pump sealing cp. Refer to repair manual section 1 66 000. N52
83 30 0 495 024 114 370 Compound press 04 07 05 Used to insert the crankshaft bed-sealing compound in to the engine block during assembly. Refer to repair manual section 11 21 500. N52
83 30 0 495 026 114 420 T0 Torx Socket 04 07 05 Used to R&R the cylinder head bolts. Refer to repair manual section 11 12 100. x N52
83 30 0 495 027 114 430 Hole Plug 04 07 05 Used to seal the oil pump holes. Refer to repair manual section 11 12 100. x N52
83 30 0 495 028 119 017 Valve Spring Cage 04 07 05 Used to R&R the cylinder head valves in conjunction with 119 000. Refer to repair manual section 11 34 552. x N52
83 30 0 495 048 114 440 Engine support fixture 04 07 05 Used in conjunction with 001 450 to support the engine for disassembly. x N52
83 30 0 495 049 114 450 Fixture 04 07 05 Used to lock the link blocks in place during assembly. Refer to repair manual section 11 37 010. x N52
83 30 0 495 050 114 460 Camshaft bearing fixture 04 07 05 Used to hold the camshaft bearing strips in place during assembly. Refer to repair manual section 11 31 028. x N52
83 30 0 495 069 121 305 Zero-Coded Cover 04 02 05 The Safety Gateway Module (SGM) connector on the wiring harness is a coded connector. Therefore, break out box 90 88 6 121 300/304 (SI B04 14 97) cannot be used in its present configuration for diagnostic work. To eliminate the need for another break out box, a zero-coded cover B.O.B. 121 300/305 has been developed.The new cover is connected to the B.O.B. by a chain. The original SGM connector cover is temporarily replaced with Zero-coded cover 121 305 for diagnostic work. Refer to SI for complete detais E60, 63, 64, 65, 66
83 30 0 495 070 110 300 Alignment Pin 04 07 05 Used to align the crankshaft TO Top Dead Center TDC. Refer to repair manual section 11 31 505. x N52
83 30 0 495 071 110 290 Brace 04 07 05 Used to R&R the vacuum pump triangular drive. Refer to repair manual section 11 66 000. x N52
83 30 0 495 072 110 320 R 04 07 05 Used to R&R the cylinder head on the engine block. Refer to repair manual section 11 12 100. N52
83 30 0 495 102 114 470 Cleaning set 04 07 05 This cleaning set is manufactured from special materials to protect the aluminum and magnesium surfaces from damage during gasket removal. x N52
83 30 0 495 105 114 480 Storage board 04 07 05 Used to store the individual cylinder head parts during work. Refer to repair manual section 11 37 010. Consists of: Storage board intake side, storage board exhaust side N52
83 30 0 495 108 009 130 Magnetic connection 1/2 04 07 05 Used to attach the torque angle tool 009 120 (SI B04 21 96) to the vehicle body when tightening the transmission tools. Refer to repair manual section 27 00 030. x N52
83 30 0 495 110 115 190 T60 Torx socket 04 07 05 Used to R&R the cylinder head. Refer to repair manual section 11 12 100. x N52
83 30 0 495 115 115 210 Protective covers 04 18 05 Used to seal the fuel injector bores on the cylinder head. Refer to repair manual section 11 12 105. x S85
83 30 0 495 116 115 220 Protective covers 04 18 05 Used to seal the throttle valve assembly. Refer to repair manual section 11 12 105. x S85
83 30 0 495 117 115 230 Pressure test fixture 04 18 05 Used to pressure test the cylinder heads for leaks. Refer to repair manual section 11 12 729. S85
83 30 0 495 118 115 240 Camshaft pres 04 18 05 Used to press the camshafts down during R&R. Refer to repair manual section 11 31 032. Order PN 83 30 0 495 155 for picture #2 bolt (Cartool PN 115 242). x S85
83 30 0 495 119 115 250 Guide Pins 04 18 05 Used when installing the connecting rods. Refer to repair manual section 11 25 530. x S85
83 30 0 495 120 115 260 Engine support plate Used to support the S85 engine on the 002 300 engine stand. S85
83 30 0 495 121 115 270 Seal Installer 04 18 05 Used to install the valve stem seals. Refer to repair manual section 11 34 560. x S85
83 30 0 495 122 115 280 Valve spring tool set 04 18 05 Used to R&R the intake and exhaust valves. Refer to repair manual section 11 34 552. x S85
83 30 0 495 123 115 290 Asembly tool 04 18 05 Used to install the bearing journals in the timing chain cover. Refer to repair manual section 11 36 148. x S85
83 30 0 495 124 115 300 Camshaft fixture TDC 04 28 05 Used to fix the camshaft at Top Dead Center (TDC). Refer to repair manual section 11 31 072. x E60 M5
83 30 0 495 125 115 310 Rear Seal Puller 04 18 05 Used to remove the rear crankshaft seal. Refer to repair manual section 11 14 151. x E60 M5
83 30 0 495 126 115 320 Alignment pin 04 18 05 Used to lock the crankshaft in Top Dead Center (TDC). Refer to repair manual section 11 31 072. x S85
83 30 0 495 127 115 330 Seal Installer 04 18 05 Used to install the front crankshaft seal. Refer to repair manual section 11 14 005. x S85
83 30 0 495 128 115 340 Tool set 04 18 05 Used to install the piston wrist pin retaining rings. Refer to repair manual section 11 25 530. x S85
83 30 0 495 129 115 350 Timing chain retainer 04 18 05 Used to hold and pretension the timing chain. Refer to repair manual section 11 12 106. x S85
83 30 0 495 130 115 360 Oil pressure adapter set 04 18 05 Used to test the VANOS oil pressure. Refer to repair manual section 11 36 009 x S85
83 30 0 495 131 115 370 VANOS locking tool 04 18 05 Used to lock the VANOS exhaust camshaft when aligning the gears. Refer to repair manual section 11 36 150. x S85
83 30 0 495 132 115 380 VANOS gauge 04 18 05 Used when adjusting VANOS to the basic setting. Refer to repair manual section 11 36 150. x S85
83 30 0 495 133 115 390 Spark plug bore covers 04 18 05 Used to seal the spark plug bore holes while performing work on the head. Refer to repair manual section 11 31 032. x S85
83 30 0 495 134 115 400 VANOS torx T20 04 18 05 Used to R&R the VANOS solenoid valve bolts. Refer to repair manual section 11 36 715. x S85
83 30 0 495 136 212 300 Clutch centering tool 04 18 05 Used to center the twin plate clutch during installation. Refer to repair manual section 21 21 000. x S85
83 30 0 495 137 230 139 Tansmission support bracket 04 18 05 Used to support the transmission during R&R. Refer to repair manual section 23 0 613. S85
83 30 0 495 138 234 100 Seal Installer 04 18 05 Used to install the input shaft seal on the GS7S47BG transmission. Refer to repair manual section 23 12 512. x 85
83 30 0 495 139 234 110 Seal installer 04 18 05 Used to install the output shaft seal on the GS7S47BG transmission. Refer to repair manual section 23 12 057. x S85
83 30 0 495 143 335 030 Seal installer 04 18 05 Used to install the final drive (215 with lock) output shaft seals (Left and Right). Refer to repair manual section 33 11 151. x S85
83 30 0 495 145 663 150 ACC adjustment Wench 04 22 05 This wrench is used to adjust ACC sensor 2 on all current and future models. Adjust sensor 2 (1) using wrench 663 150 at adjustment screws (2). Refer to repair manual section 66 31 001. Test only x All
83 30 0 495 182 332 170 Bearing installer 04 18 05 Used to install the front final drive bearing. Refer to repair manual section 33 17 004. S85
83 30 0 495 183 332 180 Bearng installer 04 18 05 Used to install the rear final drive bearing. Refer to repair manual section 33 17 005. S85
83 30 0 495 187 002 300 Engine Stand 04 06 06 NA This new engine stand (introduced @ the 2005 NAC) will accomodate all engines from the S85 and newer. Order PN 90 88 6 002 320 support arm for older V8 and V12 engines. The introduction of the S85 engine necessitated a new way of mounting the engine on a stand for assembly/disassembly. The S85 is mounted from the transmission end. The previous style stand 001 450 must not be used for mounting the S85 engine. The supplied universal flange (#2 in W002300) allows mounting of older style 4 cyl engines. Order PN 83 30 0 495 380 for N73 mounting plates. Order PN 83 30 0 495 381 for N62TU support plates. Order PN 83 30 0 495 201 for item #4 in picture. All from S85
83 30 0 495 194 612 470 AFS test cable 04 25 05 Used to troubleshoot the electric coolant (1) pumps. Used to troubleshoot active steering (AFS). The test cable is connected between the AFS (1) and the vehicle wiring harness (2) x All
83 30 0 495 196 002 320 Support Arm 04 06 06 NA Support arm required for the above engines when used with Engine Stand 88 88 6 002 300. Order PN 83 30 0 495 380 for N73 mounting plates. Order PN 83 30 0 495 381 for N62TU support plates. M73, S85, N62
83 30 0 495 220 616 210 Wiper arm remover 04 20 05 Use to remove the left and right wiper arm. Refer to repair manual section 61 61 100. x E90
83 30 0 495 231 361 335 Wheel Lock adapter set 04 10 05 NA 90 88 6 361 301=11, 302=12, 303=13, 304=14, 306=16, 307=17, 308=18, 309=19, 311=20, 312=31, 313=32, 314=33, 315=34, 316=35, 317=36, 318=37, 319=38, 321=39, 322=40, 305=15. Must also order 90 88 6 361 300 for complete set. All
83 30 0 495 235 315 200 Pliers 04 16 05 Used to R&R the low profile dust boot clamps on the front output shafts. Refer to Repair Manual Section 31 60. x E60 All-wheel
83 30 0 495 236 004 400 Torque Rotation-Angle Wrench 04 41 06 This wrench measures in the 3 to 60 Nm range. Electronic torque rotation-angle wrenches are used to tighten aluminum bolts. Aluminum bolts are identified by the blue painted head. The torque and angle of rotation are shown on the display. A visual, acoustical or vibration warning is utilized when the measured value is reached. The torque wrench does not use a calibration arm which makes torque rotation-angle easier. N52/N54
83 30 0 495 237 115 410 VANOS gauge 04 18 05 Used to remove VANOS. Refer to repair manual section 11 36 150. x S85
83 30 0 495 239 651 170 CD Magazine Eject Tool 04 14 05 The eject tool is a specially shaped plastic sleeve that is used to mechanically unlock the CD magazine (1) when it is stuck. CD changers (2) with stuck magazines no longer need to be replaced due to this problem. Refer to repair manual section 65 11. One piece will be distributed to every center free of charge. x E60, 61, 63, 64
83 30 0 495 240 221 040 Transfer case mount remover 04 16 05 Used in conjunction with 221 017 (SI B04 09 03) x E60 all wheel
83 30 0 495 241 271 430 Seal Instaler 04 16 05 Used to install the transfer case input shaft seal. Refer to repair manual section 27 21 010. x E60 All-wheel
83 30 0 495 242 271 440 Seal Installer 04 16 05 Used to install the rear-axle differential output shaft seal. Refer to repair manual section 27 21 020. x E60 all-wheel
83 30 0 495 243 271 450 Seal Installer 04 16 05 Used to install the front-axle differential output shaft seal. Refer to repair manual section 27 21 030. x E60 All-wheel
83 30 0 495 251 314 070 Support brackets 04 16 05 Used in conjunction with 314 060 (SI B04 05 05) & 002 040 (SI B04 18 91) to support the front axle carrier during R&R. Refer to repair manual section 31 11 506. E60 All-wheel
83 30 0 495 253 614 360 Seat Test Cable 04 25 05 Used to test the seat function (out of vehicle) on E90 vehicles. x E90
83 30 0 495 254 614 370 Engine test cable 04 25 05 All engine-wiring harnesses are equipped with connectors from various suppliers (Kostal, Tyco or Bosch). These connectors are coded differently. This test harness is zero coded which allows the testing of sensors and actuators such as the coolant temp sensor (1). x All
83 30 0 495 255 244 310 Seal Installer 04 16 05 Used to install the GA6HP19Z output shaft seal. Refer to repair manual section 24 13 013. x E60 all-wheel
83 30 0 495 256 004 410 Torque Rotation-Angle Wrench 04 41 06 This wrench measures in the 10 to 200 Nm range. Electronic torque rotation-angle wrenches are used to tighten aluminum bolts. Aluminum bolts are identified by the blue painted head. The torque and angle of rotation are shown on the display. A visual, acoustical or vibration warning is utilized when the measured value is reached. The torque wrench does not use a calibration arm which makes torque rotation-angle easier. N52/N54
83 30 0 495 259 510 010 Windshield test gauge 04 24 05 Test gauge 513 210 previously distributed (B04 04 97) will not work on new model vehicles. New Test gauge 510 010 will work on all BMW vehicle front and rear windscreens. This gauge is necessary for correct installation. x All
83 30 0 495 291 323 130 Steering shaft guide 04 10 98 used to guide the steering shaft bearing onto the upper spindle x E46
83 30 0 495 298 350 110 Brake pedal pivot Tool 04 20 02 Used in brake pedal campign. Refer to SI B35 50 02. Order 90 88 6 350 112 for drill only. Order 90 88 6 350 111 for template only. Or order PN 3083A133 from www.Mcmaster.com. x X5
83 30 0 495 320 610 200 Crimping set 04 27 05 shelf The crimping set consists of:1.Plastic storage case2.Crimping pliers3.Allen key for die changingThe pliers will be used on future models by changing the dies. Extra storage for future dies is included in the box. This set is always supplied without dies. Cartool PN 610 200. Refer to SI for complete detals. x All
83 30 0 495 327 610 210 Die for LSK 8 Contacts 04 27 05 This set of dies comes complete with upper, lower and positioner sections. This set of dies can only be ordered complete (all in one box). Instructions for use are included. Cartool PN 610 210. Refer to SI for complete details. x All
83 30 0 495 328 610 220 Die for SLK 2.8 Contacts 04 27 05 This set of dies comes complete with upper, lower and positioner sections. This set of dies can only be ordered complete (all in one box). Instructions for use are included. Cartool PN 610 220. Refer to SI for complete detais. All
83 30 0 495 332 611 370 Wiper Alignment Gauge 04 05 06 Used to align the E91 rear window wiper arm to the drive unit during installation. Refer to repair manual section 61 62 060. Cartool PN 611 370 x E91
83 30 0 495 339 334 350 Bearing Tool 04 05 06 Used to R&R the rubber bearing for the rear differential mount. Refer to repair manual section 33 17 005. 1. Disc for removing 2. Disc for mounting 3. Support disc for mounting. 4. Bearing shells (2) 5. Fixing ring for bearing shells. 6. Clamp ring 7. Support disc 8. Shaping disc x E90/91
83 30 0 495 346 616 100 Windshield Wiper Arm Adjustment Gauge 04 13 06 The contact angle between the windshield and the wiper blade is critical. An improperly adjusted wiper arm may chatter or rub and will give uneven wiper operation. The introduction of the new generation wiper arms on the E90 and E91 vehicles means that the earlier distributed adjustment gauges can no longer be used. This new adjustment gauge can be used on new and prior model vehicles. Refer to Repair Manual sections 61 61 01 and 61 61 010. Refer to SI for mor edetails x E90, E91
83 30 0 495 355 323 146 Camber adjuster parts 04 05 06 Used in conjunction with 90 88 6 323 145 to adjust the front wheel camber. ·Remove PN 323 144 from tool 323 145. ·Discard tool 323 144 ·Replace it with 83 30 0 495 355 (323 146).·Refer to repair manual section 32 00 610 for tool operation. x E90/91
83 30 0 495 356 323 147 Camber adjuster parts 04 05 06 Used in conjunction with 90 88 6 323 145 to adjust the front wheel camber. ·Remove PN 323 144 from tool 323 145. ·Discard tool 323 144 ·Replace it with 83 30 0 495 355 (323 146).·Refer to repair manual section 32 00 610 for tool operation. Cartool # 323 147. x E90/91
83 30 0 495 374 314 080 Support Adapters 04 26 07 Used in conjunction with Transmission stand 83 30 0 490 133 (002 030) to support the front axel carrier during removal and installation. Refer to Repair Manual section 31 11 506 for details. E90 E91
83 30 0 495 380 002 323 Engine support Arm 04 17 06 Used in conjunction with engine stand 002 300 and support arm 002 320 to support the 12 cylinder N73. N73
83 30 0 495 381 002 325 Engine support plate 04 17 06 Used in conjunction with engine stand 002 300 and support arm 002 320 to support th e8 cylinder N62TU. N62TU
83 30 0 495 382 610 300 Electrical Contact Release Kit 04 08 06 NA The contact release kit has been updated and modified to fully meet the needs set forth by the vehicle connector manufacturers. Utilizing this kit ensures that the connectors will not be harmed during R&R. x All
83 30 0 495 403 610 321 Pin Release tool 04 08 06 Used to remove SLK 2.8mm pins. Thios is a replacement part. It was originally included with kit610 300 (83 30 0 495 382) SI B0408 06. All
83 30 0 495 444 241 360 Converter Locking Device 04 26 07 Used to lock the converter in place during transmission removal and installation. Refer to Repair Manual section 24 00 023 for details. x E90 E91
83 30 0 495 446 240 200 Transmission Support Fixture 04 15 07 Used to support all manual and automatic transmissions in conjunction with assembly stand 001 450 or 002 300. This special tool supersedes tool PN 240 180 (83 30 0 491 652). All
83 30 0 495 448 114 650 Oil filter wrench 04 23 87 used to R and R oil filters E30, 325IX
83 30 0 495 449 212 270 Clutch Alignment Tool 04 14 07 Used to align the clutch on the N54 engine. Refer to repair manual section 21 21 500. x E9X, E60
83 30 0 495 477 610 230 Crimping Die 04 10 06 The crimping die for DFK 4 contacts is used with the crimping handle (2) in set PN 610 200 (83 30 0 495 320 SI B04 27 04). Crimping die 610 230 is stored in the kit box. x E90/91
83 30 0 495 484 009 324 Trim Remover 04 04 06 In kit 009 310 Cartool PN 009 324. Must be used when removing the window cavity cover trim to prevent damage. The tool removes the trim from the inside preventing paint damage. Refer to repair manual section 51 21 300. All
83 30 0 495 485 315 220 Support 04 36 06 Used to hold the wheel hub in place when removing or replacing the spring strut. Refer to repair manual section 31 31 000. E90, E91
83 30 0 495 486 241 370 Torque converter brace 04 36 06 Used to hold the torque converter in place when performing an R&R on the 6HP19 transmission. Refer to repair manual section 24 00 030. x E90, E91
83 30 0 495 495 612 240 CAS Test Cable 04 11 06 CAS Test Cable 41 Pin. Used to test the CAS module as described by the appropriate GT1 diagnostic test. x E90/91
83 30 0 495 498 234 050 Universal transission holder 04 13 08 Used to support all manual and automatic transmissions in conjunction with 002 030. All
83 30 0 495 505 510 300 Roller 04 28 06 Used to install strips, rubber seals (1) and noise insulation. The wheel is made to a specified hardness so as to not harm the painted surfaces. All
83 30 0 495 506 009 350 E box template Used to remove material from the sode of the Ebox to install the aux wire harness. Used with 009 360. E85/60
83 30 0 495 507 009 360 Template Used to remove material from the sode of the Ebox to install the aux wire harness. Used with 009 350. E85/60
83 30 0 495 519 311 071 Ball Joint Tester Adapter 04 14 06 A new Ball Joint Adapter Plate has been developed for use on vehicles with aluminum Ball Joint end covers. The adapter plate is used with Ball Joint Tester 83 30 0 494 326 (Cartool 31 060 SI B04 03 03). The adapter plate must be used with adhesive pad 83 30 0 495 558. Refer to repair instructions 31 12 023. x E46 M3
83 30 0 495 528 110 480 Crankshaft Alignment Pin 04 21 07 Used to hold the crankshaft at Top Dead Center (TDC) when adjusting the camshaft timing. For more details, refer to repair manual section 11 31 505. x E85 S54
83 30 0 495 529 234 030 Pilot Bearing Tool 04 19 07 Used in conjunction with a grease gun to R&R the new style pilot bearing on the GS6-53BZ transmission. The pilot bearing is located in the transmission input shaft. Refer to Repair Manual Section 11 22 513. E92 N54
83 30 0 495 534 641 300 AC Sprayer Wand 04 02 07 Used in conjunction with AC disinfectant sprayer (SI B04 03 02) to clean and disinfect the AC system on vehicles that exhibit a musty odor. Refer to Repair Manual section 64 51 001. E70
83 30 0 495 551 335 040 Opened Jaw Spanner 04 24 06 Used in conjunction with 335 070 to R&R the driveshaft inner nut (final drive end). Refer to repair manual section 26 11 000. x E90, E91, E92 and E70 with N54 B30
83 30 0 495 552 335 050 Multi-Point Ring Spanner 04 24 06 Used in conjunction with 335 070 to R&R the flange nut on the final drive. Refer to repair manual section 33 11 021. x E90, E91, E92 and E70 with N54 B30
83 30 0 495 553 335 060 Multi-Toothed Socket 04 24 06 Used in conjunction with 335 070 to hold the input shaft on the final drive when replacing the seal. Refer to repair manual section 33 11 021. x E90, E91, E92 and E70 with N54 B30
83 30 0 495 554 335 070 Telescoping Extension 04 24 06 Used in conjunction with 335 040 and 335 050. Refer to 335 040 and 335 050 above for details and repair manual section 33 11 021 x E90, E91, E92 and E70 with N54 B30
83 30 0 495 555 614 328 Universal crimping die 04 32 06 A universal crimping die has been developed to aid in the repair of a large number of contacts. The die is made to repair contacts with a wire diameter of 0.35 ¿ 2.5 mm. Refer to SI for details. x All
83 30 0 495 558 311 079 Adhesive Pad 04 14 06 Used with PN 83 30 0 495 519 to attach the adapter plate to the aluminum Ball Joint end cover. One order equals 10 pieces. The Pad has adhesive on both sides. Refer to repair instructions 31 12 023. x E46 M3
83 30 0 495 560 121 220 Sparl plug socket 04 30 06 Used to R&R the new style spark plugs. It will be necessary to use a short impact extension between the socket 121 220 and the torque limiter 121 172. Do not use an extension with a swivel. Refer to repair manual section 12 12 011. x N54
83 30 0 495 567 315 250 Universal Axle Support 04 25 07 The Universal Axle Support is used in conjunction with hydraulic jack P.N. 83 30 0 490 133 (002 030) to support front and rear axle assemblies during removal and replacement. Superceeds 83 30 0 492 296. All
83 30 0 495 575 334 426 Final Drive Support Adapter 04 23 07 This tool is used in conjunction with 334 420 (83 30 0 494 611) and 002 030 (83 30 0 490 133) to support the final drive during removal and replacement. Refer to the E85 repair manual, section 33 10 010 for complete details. E85 (M)
83 30 0 495 576 115 160 Lift Latches 04 20 06 Used to lift out the radiator assembly. Refer to Repair Manual Section 17 00. x Alpina B7
83 30 0 495 577 115 170 Belt tensioner tool 04 20 06 Used to relax the tension on the serpentine belt. Refer to Repair Manual Section 11 28. x Alpina B7
83 30 0 495 578 610 325 JPT conector release tool 04 19 06 NA Insert special tool 610 325 into the relevant housing release slots and depress the locks. Pull the contact from the housing. x All
83 30 0 495 579 135 255 Steering Shaft Adapter 04 31 06 Used in conjunction with 135 250 (SI B04 18 01, 83 30 0 493 321) to remove the steering shaft. Refer to repair manual section 32 32 001. E85
83 30 0 495 580 324 270 Steering shaft installer 04 31 06 Used to install the steering shaft and steering shaft bearing. Refer to repair manual section 32 32 001. E85
83 30 0 495 588 161 080 Hose Guide 04 26 06 Starting with 9/2006 production, a new style fuel filler flap will be gradually introduced on all models. This special tool is required in the workshop to remove and refill fuel from the tank during repair work without damage to the flap. The tool has two different size ends. One for Gasoline (18mm), the other for Diesel (24mm). x All
83 30 0 495 589 510 310 Clamp Lever 04 12 07 Used to remove the headliner on the E93 RHT and for releasing trim on all model series. Refer to Repair Manual section 54 37 040. E93
83 30 0 495 590 513 300 Window Adjustment Wrench 04 22 06 To prevent leaks and wind noises the door windows must be correctly adjusted after repairs. The following tools are used to make the adjustments without damage to the doors painted surfaces. Insert tool into door adjustment opening and place end on adjustment screw. To assist in this application the tool has a mark (1) that must be even with the door opening. Refer to repair manual section 51 32 154. 92/93
83 30 0 495 591 513 310 Ratchet Wrench 04 22 06 This wrench has been preconfigured to the geometry of the door. It is used in a square drive torque wrench. The torque wrenches are available through parts (refer to SI B04 29 03) or through Baum Tools @ 800 848 6657. E92/93
83 30 0 495 593 335 080 Seal Installer 04 24 06 Used to install the final drive input shaft seal. Refer to repair manual section 33 11 021. x E90, E91, E92 and E70 with N54 B30
83 30 0 495 597 242 354 Seal Removal Tool 04 11 07 Used to remove the input shaft seal. Refer to repair manual section 24 31 011 x GM6 Transmission
83 30 0 495 598 244 350 E10 Torx Socket 04 11 07 Used to R&R the securing bolts for the Mechatronic (or VB-TEHCM asm). Refer to repair manual section 24 34 562. x GM6
83 30 0 495 599 244 360 Seal Removal Tool 04 11 07 Used to remove the output shaft seal. Refer to repair manual section 24 13 013. x GM6
83 30 0 495 600 244 370 Seal Installation Tool 04 11 07 Used to install the output shaft seal. Refer to repair manual section 24 13 013. x GM6
83 30 0 495 601 244 380 Seal Installation Tool 04 11 07 Used to install the selector shaft seal. Refer to repair manual section 24 14 002. x GM6
83 30 0 495 602 244 390 Seal Removal Tool 04 11 07 Used in conjunction with 135 250 (SI B04 18 01) to remove the oil filter seal. Refer to repair manual section 24. x GM6
83 30 0 495 603 244 400 Seal Installation Tool 04 11 07 Used to install the oil filter seal. Refer to repair manual section 24. x GM6
83 30 0 495 604 541 110 Sunroof centering pins 04 23 06 The sunroof centering pins were developed to eliminate wind noise and rain leaks when the sunroof cassette is replaced. The pins precisely align the cassette in the roof opening. Two pins come with each order. Refer to Repair Manual section 54 13 080. This picture shows how to use the pins on the E61, E83 and E91. On the E53, only the front centering hole is provided. E53,61,83,91
83 30 0 495 605 009 140 Rotation Angle Measuring Gauge 04 25 06 Used to tighten the crankshaft central bolt to the correct angle. Refer to repair manual section 11 31 051. N54, N54
83 30 0 495 623 334 285 Installation Shim 04 33 06 Used in conjunction with 334 182 (SI B04 02 96), 334 465 (04 05 05) and 334 466 to properly mount the rear differential bushing. Refer to repair manual section 33 17 005. E85 E86
83 30 0 495 626 212 280 Clutch Centering Tool 04 34 06 Used to center the drive plate to the pressure plate when installing the clutch. Refer to repair manual section 21 21 500. x E60 M5
83 30 0 495 627 233 240 Input shaft seal tool 04 34 06 Used to install the input shaft seal. Refer to repair manual section 23 12 510. x E60 M5
83 30 0 495 676 610 326 ¿MQS¿ Connector Release Tool 04 19 06 NA Used to release and remove the ¿micro standard¿ and ¿MQS¿ connectors. x All
83 30 0 495 677 610 327 Insertion Tool 04 19 06 NA Used to insert 0.64 to 1.2 mm contacts with sealing ring. The tip of the insertion tool is shaped to prevent damage to the seal. Place the wire (1) into the tool (2) and insert seal (3) into the connector housing. Never press the seal into the connector with a sharp tool. Damaged seals must not be used. x All
83 30 0 495 678 610 328 Insertion Tool 04 19 06 NA Used to insert 2.8 to 4.8 mm contacts with sealing ring. The tip of the insertion tool is shaped to prevent damage to the seal. Place the wire (1) into the tool (2) and insert seal (3) into the connector housing. Never press the seal into the connector with a sharp tool. Damaged seals must not be used. x All
83 30 0 495 680 610 331 SLK Connector Release Tool 04 19 06 NA Used to remove 5.8 mm SLK contacts. Insert the tool into the housing (1) and release the contact. x All
83 30 0 495 682 335 100 Spring Tensioner 04 39 06 Used to R&R the rear springs on vehicles without automatic ride height option. Refer to repair manual section 33. Application note: Never use an air impact driver on the spring tensioner as damage can result. Instead, use the supplied special tool. Always use all BMW Spring Compressors in accordance with use and safety procedures as stated in the BMW repair instructions. Never try to use or repair a damaged tool. x E70
83 30 0 495 723 114 284 Fixture Screws 04 21 06 Used in conjunction with 114 280 (SI B04 07 05) to hold the camshaft at Top Dead Center (TDC). Refer to repair manual section 11 31 005. N54
83 30 0 495 726 118 510 Spray Jet Fixture 04 25 06 Used to hold the oil spray jets in the proper position. Refer to repair manual section 11 21 531. N54
83 30 0 495 727 118 520 Gauge 04 21 06 Used to align the camshaft sensor gears. Refer to repair manual section 11 31 505. N54
83 30 0 495 728 118 530 Vacuum Pump Tool 04 21 06 Used to R&R the vacuum pump sealing cover. Refer to repair manual section 11 14 010. N54
83 30 0 495 736 118 540 Support Plate 04 25 06 Used to mount the engine on the engine stand (83 30 0 495 187 - SI B04 06 06). N54
83 30 0 495 739 118 550 Bearing Fixture 04 30 06 Used to hold the camshaft bearings in place when fitting the camshaft. Refer to repair manual section 11 31 025. x N54
83 30 0 495 747 118 580 T60 Torx Socket 04 21 06 Used to R&R the cylinder head bolts. Refer to repair manual section 11 12 100. N54
83 30 0 495 748 118 590 Connecting Rod Guides 04 03 07 Used to safely place the piston with connecting rods into the engine. Refer to Repair Manual section 11 25 530. N54
83 30 0 495 749 118 610 WAF 5 Hex Socket 04 21 06 Used to R&R the high pressure pump. Refer to repair manual section 13 51 017. N54
83 30 0 495 750 118 640 E 10 Torx 04 30 06 Used to R&R the oil pump triangular drive. Refer to repair manual section 11 41 010. x N54
83 30 0 495 751 118 620 WAF 10 Socket 04 30 06 Used to R&R the ground connection for the fuel injectors during valve cover removal. Refer to repair manual section 11 12 000. x N54
83 30 0 495 752 118 650 Brace 04 21 06 Used to R&R he oil pump drive sprocket. Refer to repair manual section 11 66 000. N54
83 30 0 495 753 118 660 Flywheel Holder 04 30 06 Used to hold the flywheel in place with the automatic transmission installed. Refer to repair manual section 11 23 010. x N54
83 30 0 495 754 118 670 Clamp 04 25 06 Used to R&R the charge air pipe. Refer to repair manual section 11 61 362. N54
83 30 0 495 755 130 180 Injector remover 04 30 06 Used to remove stuck injectors. Refer to repair manual section 13 64 501. x N54
83 30 0 495 756 130 190 Assembly Set 04 30 06 Used to R&R the Teflon rings on the injectors. x N54
83 30 0 495 762 221 100 Mount Remover 04 39 06 Used to R&R the transfer case rubber mount together with 221 010 (04 50 99). Refer to repair manual section 22. x E70
83 30 0 495 763 271 460 Seal Installer 04 39 06 Used to install the transfer case input shaft seal. Refer to repair manual section 27. x E70
83 30 0 495 764 271 470 Seal Installer 04 39 06 Used to install the transfer case output shaft seal. Refer to repair manual section 27. x E70
83 30 0 495 765 271 480 Seal Installer 04 39 06 Used to install the transfer case output shaft seal. Refer to repair manual section 27. x E70
83 30 0 495 769 180 110 Gauge 04 25 06 Used to hold the exhaust manifold in place during installation. Refer to repair manual section 18 32 050. N54
83 30 0 495 770 118 680 Adapter 04 03 07 Used to support the engine during lifting and lowering (R&R). Refer to Repair Manual section 11 00 050. N54
83 30 0 495 771 610 110 Heater Test Cable 04 40 06 Used to diagnose the 3rd seat heater. x E70
83 30 0 495 772 610 120 DME Test Cable 04 40 06 Used to diagnose connector number 3 on the DME. x E70
83 30 0 495 773 610 130 Electric Coolant Pump Test Cable 04 40 06 Used to diagnose the electric coolant pump. x E70
83 30 0 495 774 610 140 Air Mass Meter Test Cable 04 40 06 Used to diagnose the hot-film air mass meter. x E70
83 30 0 495 775 610 150 Tailgate Test Cable 04 40 06 Used to diagnose the left side tailgate drive. x E70
83 30 0 495 776 610 160 Tailgate Test Cable 04 40 06 Used to diagnose tailgate connector 1. x E70
83 30 0 495 777 610 170 Steering Lock Test Cable 04 40 06 Used to diagnose the steering column lock. x E70
83 30 0 495 799 312 310 Thrust rod remover Used to press the trust rod out of the wheel carrier. Refer to repair manual section 31 21 151. Replaced by 312 310. E83
83 30 0 495 814 721 200 Rivet Extractor 04 01 07 The E92 Head protection System airbag (HPS) is attached to the vehicle with special rivets not bolts. If removal of the HPS becomes necessary, it is important not to let the back side of the rivet fall into the body cavity. Body noises (rattle) might be evident. This tool is adjustable to fit into body cavities and capture the back side of the rivet before it is lost in the body cavity. Refer to Repair Manual Section 72 12 060. A universal rechargeable rivet gun may be ordered using PN 81 43 0 301 745 if required. E92
83 30 0 495 829 314 150 Mount Remover 04 39 06 Used to R&R the lower control arm rubber mount. Refer to repair manual section 31 12. x E70
83 30 0 495 830 512 240 Hood Support 04 39 06 Used to support the engine hood in the service position. Refer to repair manual section 51. x E70
83 30 0 495 850 000 452 Engine Support Feet 04 13 07 Used in conjunction with 000 200 to support the engine. Refer to Repair Manual section 11 00 670. E70
83 30 0 495 851 335 120 Shaft Remover 04 39 06 Used to R&R the final drive output shaft. Refer to repair manual section 33. x E70
83 30 0 495 852 314 100 Support Adapters Used to support the front axle during R&R. In conjunction with 002 030. E70
83 30 0 495 858 314 160 Seal Installer 04 39 06 Used to install the output shaft seal on the front axle final drive. Refer to repair manual section 31 51 015. x E70
83 30 0 495 860 335 130 Seal Installer 04 39 06 Used to install the output shaft seal on the final drive. Refer to repair manual section 33. x E70
83 30 0 495 863 335 150 Mount Remover 04 39 06 Used to R&R the rear rubber mount on the final drive. Refer to repair manual section 33. x E70
83 30 0 495 864 335 160 Mount Remover 04 39 06 Used to R&R the front rubber mount on the final drive. Refer to repair manual section 33. x E70
83 30 0 495 865 335 170 Mount Remover 04 39 06 Used to R&R the rubber mount on the rear axle carrier. Refer to repair manual section 33. x E70
83 30 0 495 885 002 260 Hoist Fixture 04 39 06 Must be used to secure the vehicle to the hoist when removing and installing major components such as but not limited to front axle carrier, rear axle carrier and engine/transmission. Refer to repair manual section 00. x E70
83 30 0 495 899 314 170 Locking Tool 04 39 06 Used to lock the universal joint in place while removing and installing the output shaft. Refer to repair manual section 31. x E70
83 30 0 495 908 371 150 Hydraulic Line Tool 04 02 07 Used to R&R the hydraulic lines on the E70 Dynamic Drive (Sport Package) and the N54 fuel injector lines. Refer to Repair Manual sections 13 53 192 (N54) and 37 20 001 (E70). x E70 & N54
83 30 0 495 995 003 070 Floor Mat Awl 04 18 07 A 3 mm hole must be punched into floor mats in order to affix them to the floor. Follow the instructions included with the floor mats. x All
83 30 0 496 006 312 247 Ball Joint Remover 04 13 07 Used in conjunction with 312 240 to remove the tension strut ball joint. Refer to Repair Manual section 31 12 050. x E70
83 30 0 496 007 004 430 Double Torx Tool 04 12 07 This tool has a T20 on one side and a T30 on the other. It is designed for the tight spaces during R&R of roof shell #3 and the headliner. Refer to Repair Manual section 54 37 040. E93
83 30 0 496 009 335 200 Rear diff. support 04 22 08 This tool is used to support the rear differential for removing and installation. For more details, refer to repair manual section for E70, 33 10 010. E70, E90, E92
83 30 0 496 028 540 110 Cowl Panel Gauge 04 12 07 Used to calibrate the base plate at the cowl panel. This is the zero point for all measuring and calibration work on the RHT. Refer to Repair Manual section entitled Calibrating base plate (cowl panel lock). E93
83 30 0 496 029 540 120 Basic Gauge (1-3) 04 12 07 NA The basic gauge specifies the settings on the X (longitudinal), Y (lateral) and Z (vertical) axis. The gauge is used for the following operations. Calibrating/examining the coupling Calibrating the coupling after the roof module has been R&R Calibrating the roof module consoles E93
83 30 0 496 033 540 130 Coupling Gauge (1-2) 04 12 07 RHT tool. Refer to SI for details. E93
83 30 0 496 036 540 140 Roof Module Console Gauge 04 12 07 1. Left gauge 2. Right gauge 3. Transverse strut Only use tool 540 140 with tool 540 120. The roof module consoles are only calibrated after performing body repairs. Refer to Repair Manual section entitled Calibrating roof module consoles. E93
83 30 0 496 039 540 150 Rear Module Console Gauge 04 12 07 1. Left gauge 2. Right gauge The rear module consoles are only calibrated after performing body repairs. Refer to Repair Manual section entitled Calibrating rear module consoles. E93
83 30 0 496 040 540 170 Service Position Fixture 04 12 07 Tension strap and securing hooks are used to prevent the RHT from dropping during adjusting work. An example is when removing the headliner or roof shell #3. The hydraulic pressure drops off after 2 hours. E93
83 30 0 496 041 540 160 Emergency Tool (1-3) 04 12 07 This tool is used to open and close the RHT. It consists of a slide tool (1), a pulling tool (2) and an adapter (3). Must use 540 240 to support module during emergency tool application. Do not attempt to use this tool if you have not taken the E93 Training Course ST701. E93
83 30 0 496 042 540 180 Barrel screw socket 04 12 07 RHT tool. Refer to SI for details. E93
83 30 0 496 043 540 190 Lock Nut Socket 04 12 07 RHT tool, refer to SI fro details. E93
83 30 0 496 044 540 220 Cover for Separator Module 04 12 07 Used to eliminate the risk of triggering the rollover protection. The tool is inserted into the separator module. Refer to Repair Manual section 54 37 130. E93
83 30 0 496 046 510 020 Rear Window Assembly Aid (1-2) 04 12 07 This tool consists of the left side tool (1) and the right side tool (2). It is used when installing the rear window. Roof shell #3 must be removed so the rear window is glued without tension. This tool is needed to align the rear window X-axis setting correctly. The Y-axis is aligned by centering roof shell #3. The Z-axis is aligned by the spacers. Refer to Repair Manual section entitled Removing and installing rear window for E93. E93
83 30 0 496 047 540 230 Crimping Die 04 12 07 Used in conjunction with 610 200 (SI B04 27 05) to crimp the sleeve on the headliner tensioning straps when replacement is necessary. E93
83 30 0 496 048 540 200 Bridging connector 04 12 07 Used to open and close the roof module when the rear module has been removed. Refer to Repair Manual section 54 37 160. E93
83 30 0 496 049 540 000 Set 1.1 Roof Module Adjustment gauges 04 12 07 NA The E93 RHT tools come in 4 kits. Refer to the SIB for details. x E93
83 30 0 496 055 009 450 Torque Wrench 04 12 07 RHT tool, refer to SI for details. E93
83 30 0 496 058 510 320 Window Assembly Aid (1-2) 04 12 07 Used to correctly adjust the door side windows along the X-axis (E92&E93). Refer to Repair Manual section 51 32 154. E93
83 30 0 496 061 244 166 Converter Bracket 04 11 07 Used to hold the converter in place during transmission R&R. Refer to repair manual section 24 00 030. x GM6
83 30 0 496 062 332 200 Puller A21 This tool replaces tool 332 110. 332 111 - 332 203 332 114 - 332 204 332 115 - 332 208 332 116 - 332 201 332 117 - 332 207 332 118 - 332 205 332 119 - 332 206 E30, All
83 30 0 496 064 332 202 Special Spanner 04 13 07 Used in conjunction with 312 100, 312 200 and 335 070 to remove the output flange. Refer to Repair Manual section 31 60. x E70
83 30 0 496 072 540 240 Assembly Supports 04 12 07 Used to support the rear RHT module when there is no hydraulic pressure in the system. E93
83 30 0 496 076 009 470 Gap Gauges 04 12 07 Used to check the gap dimensions on the RHT. This tool will also be used on future models. E93
83 30 0 496 083 371 160 WAF24 Ring Spanner 04 13 07 Used to R&R the ARS pressure accumulator. Refer to Repair Manual section 37 11. x E70
83 30 0 496 084 111 240 Assembly Set 04 13 07 Used to install the drive belt. Refer to Repair Manual section 11 28 010. x E70
83 30 0 496 090 540 020 Set 2.1 Lifting Frame set for RHT 04 12 07 NA The E93 RHT tools come in 4 kits. Refer to the SIB for details. E93
83 30 0 496 091 540 040 et 1.2 Mechanical Tools for RHT 04 12 07 NA The E93 RHT tools come in 4 kits. Refer to the SIB for details. x E93
83 30 0 496 092 540 030 Set 2.2 Gauge set for RHT 04 12 07 NA The E93 RHT tools come in 4 kits. Refer to the SIB for details. E93
83 30 0 496 201 513 303 Door Window Adjustment tools 04 04 08 This tool is used in conjunction with tool 513 304 and 513 300 to adjust the door glass. For more details, refer to repair manual section 51 32 154. x E82, E83
83 30 0 496 202 513 304 Door Window Adjustment tools 04 04 08 This tool is used in conjunction with tool 513 303 and 513 300 to adjust the door glass. For more details, refer to repair manual section 51 32 154. x E82, E83
83 30 0 496 222 645 120 Testing Adapter Set for A/C System Components 04 24 08 This tool is used for leak-testing the air-conditioning system condenser and evaporator. These adapters can only be used in conjunction with the following tools and equipment: 1. Nitrogen (in pressurized bottles) - Not supplied 2. Pressure leak down gauge with a measuring range of at least 10 bar to be supplied; see below For more details, refer to Repair Instructions: 1. 645 121 (83 30 0 496 223) Connecting hose 2. 645 122 (83 30 0 496 224) Testing adapter for air conditioning condenser 3. 645 123 (83 30 0 496 258) Plug for air conditioning system condenser 4. 645 124 (83 30 0 496 259) Test adapter for evaporator E81, E82, E87, E88, E90, E91, E92, E93 5. 645 125 (83 30 0 496 260) Test adapter for evaporator E46, E83, E70 6. 645 126 (83 30 0 496 299) Test adapter for evaporator ¿ E60, E61, E63, E64 7. 645 127 (83 30 0 496 300) Test adapter for evaporator E85, E86 x All
83 30 0 496 269 119 990 Engine Brace 04 01 08 This tool is used to hold the engine in place when removing the transmission. For for details, refer to repair manual section 23 00 018. x E92 M3 with S65
83 30 0 496 270 119 970 Camshaft Fixture Set 04 01 08 This tool is used to align and fix the camshaft at Top Dead Center (TDC) during assembly. x E92 M3 with S65
83 30 0 496 274 119 980 Extraction Tool 04 01 08 This tool must be used to remove teh ignition coil, or damage to the coil and surrounding area may occur. For more details, refer to repair manual section 12 13 512. x E92 M3 with S65
83 30 0 496 287 002 326 Engine Support Plates 04 03 08 This tool is used in conjunction with engine stand 002 300 and support arm 002 320 to support the 12 cylinder N73 M73, N73, N62, S62
83 30 0 496 288 002 327 Engine Support Plates 04 03 08 This tool is used in conjunction with engine stand 002 300 and support arm 002 320 to support the S62 engine. M73, N73, N62, S62
83 30 0 496 293 315 230 Strut Tool 04 01 08 This tool is used to pull the front spring strut into the steering knuckle. 1. 315 231 (83 30 0 496 294) Body 2. 315 232 (83 30 0 496 295) M10 with spindle and fixture 3. 305 233 (83 30 0 496 296) Nut/bearing x E92 M3 with S65
83 30 0 496 310 334 286 Bushing press sapcer 04 02 08 This tool is used in conjunction with the following special tools to remove and replace the rear differential rubber mount. For more details, refer to repair manual section 33 17. 1. 334 280 83 30 0 494 048 2. 334 450 83 30 0 494 928 3. 334 460 83 30 0 494 929 4. 334 180 83 30 0 492 426 x E83, E85
83 30 0 496 312 244 340 Fill plug tool Used to R&R the oil filler plug in order to fill the transmission fluid. Refer to repair manual section 24 11 007. E6x, E9X, E81, E87
83 30 0 496 315 413 200 Roof Clamp Set 04 05 08 The clamp set is used for securing the CFK rood in place when glueing. For more details, refer to Repair Manual, section 41 31 000. 1. 413 201 (83 30 0 496 201) Locking pliers 2. 413 202 (83 30 0 496 317) G-clamp 3. 413 203 (83 30 0 496 318) Preformed sections 4. 413 204 (83 30 0 496 319) Preformed sections E92 M3
83 30 0 496 346 119 950 Valve Spring Collar 04 11 08 This tool is used in conjunction with the valve spring toolset (83 30 0 495 122) for fitting and removing the valve collets. For more details, refer to repair instructions for Series E92, section 11 34 552. x E92 M3
83 30 0 496 350 119 960 Pressure Test Cover 04 11 08 This tool is used in conjunction with the pressure test fixture (83 30 0 495 117) for testing the cylinder head for leaks. For more details, refer to repair instructions for Series E92, section 11 12 729. E92 M3
83 30 0 496 355 315 270 Tension Strap 04 11 08 This tool is used in conjunction with the tension strap set (83 30 0 494 928) for pressing the bearing of the tension rod in and out. For more details, refer to repair instructions for Series E92, section 31 12 138. x E92 M3
83 30 0 496 359 119 890 Gauge 04 07 08 This tool is used for fixing the camshaft in place when adjusting the valve timing. For more details, refer to repair instructions for N63 engine, job item 11 31 070. 1. 119 891 Rotary Handle 2. 119 892 Bridge 3. 119 893 Gauges 4. 119 894 Adapter N63 x N63 engine
83 30 0 496 360 119 900 Chain tensioner 04 07 08 This tool is used for pre-tensioning the timing chain when adjusting the valve timing. For more details, refer to repair instructions for N63 engine, job item 11 31 070. x N63 engine
83 30 0 496 365 118 090 Brace 04 07 08 This tool is used for unscrewing the central screw. For more details, refer to repair instructions for N63, job item 11 23 010. x N63 engine
83 30 0 496 366 118 570 TDC Alignment tool 04 07 08 This tool is used in conjunction with 11 9 190 for aligning the engine in Top Dead Center (TDC). For more details, refer to repair instructions for N63 engine, job item 11 31 070. x N63 engine
83 30 0 496 369 118 920 Oil pump brace 04 07 08 This tool is used in conjunction with 11 9 280 for removing the oil pump hub. For more details, refer to repair instructions for N63, job item 11 41 000. x N63 engine
83 30 0 496 370 118 930 Engine Support 04 07 08 This tool is used in conjunction with 00 2 300 for holding up the engine on assembly stand. For more details, refer to repair instructions for N63 engine, job item Assembly stand. x N63 engine
83 30 0 496 388 330 100 Fixture 04 08 08 This tool is used for removing and fitting the rear rubber mount on the rear axle final drive. For more details, refer to repair instructions for Series E92, section 33 17 005 E90, E92, E93 M3
83 30 0 496 404 330 110 Mouldings (set) 04 10 08 This tool is used in conjunction with 234 020 and item 1, 002 030, hydraulic jack for supporting the rear-axle final drive. E71, E70
83 30 0 496 405 330 120 Drift 04 10 08 This tool is used for fitting the input shaft sealing ring on the rear axle final drive. For more details, refer to repair instructions for E71, section 33 11 021. x E71, E70
83 30 0 496 406 330 130 Drift 04 10 08 This tool is used for fitting the output shaft sealing ring on the rear axle final drive. For more details refer to repair instructions for section E71, section 33 10 021. x E71, E70
83 30 0 496 408 118 080 Pressing-off Device 04 07 08 This tool is used for checking the cylinder head for leaks. For more details, refer to repair instructions for N63 engine, job item 11 12 729 x N63 engine
83 30 2 148 852 Locking Hook Connectors 04 20 08 The locking hook connectors on the D-CAN cables have a tendency to break over time. New locking hook connectors are now available for the replacement of broken connectors. 1. Locking Hook Connectors All
84 11 1 468 739 Transfer kit 04 03 95 Allows identity transfer for CMT 2000VR x All
88 88 0 000 045 PLCC extraction tool 04 17 95 used to remove EPROMs from CMT 3000 phones x E38
88 88 0 000 117 Compression stroke indicator 04 22 95 used to indicate when cylinder 1 is in the compression stroke without removing the valve covers No longer available. x M60
88 88 5 000 362 Injector leak test kit 04 17 90 used to check injectors for leaks. See SIB 13 08 90 for complete details x All
88 88 6 002 000 Torsion meter 04 03 81 used to measure friction x All Early
88 88 6 002 103 T25 torx socket 04 01 83 1 used to R&R sliding roof x E30
88 88 6 002 120 T10 torx wrench 04 14 88 1 used to R&R the rear power distribution box cover x E32
88 88 6 004 210 Reamer kit 04 18 87 used to ream valve guides. See SIB 11 11 86 for details x M20, S14
88 88 6 004 220 Valve guide reamer set 04 03 96 used to ream valve guides (6mm) x M60, M52, M50, M42
88 88 6 008 550 008 550 Puller used to remove rear wheel bearing x E21
88 88 6 009 210 wiper gauge 04 21 89 superceeded by 90 88 6 009 230 x E32 E34
88 88 6 110 070 Engine hoist frame 04 09 97 used to remove and install 4 cylinder engines x M44, M42
88 88 6 110 080 Engine adapters 04 22 92 used to mount engine on stand M60
88 88 6 110 192 Guide tube shaft 04 19 96 used with 90 88 6 110 342 to depress valve springs x M44, M52
88 88 6 110 210 Valve board 04 22 92 used to support valves when using 88 88 6 001 490 M60
88 88 6 110 341 Valve spring depressor 04 01 97 used to R&R valve springs. x M73
88 88 6 110 342 Pressure lever 04 14 96 used to depres valve spring compressor 90 88 6 110 344 x M52
88 88 6 111 030 Pressure test set 04 01 84 used to pressure test head x 524TD
88 88 6 111 420 Pressure fixture 04 21 88 used to pressure test engine head E31, E32
88 88 6 111 470 Head fixture 04 22 92 used to pressure test head M60
88 88 6 112 010 112 010 Puller used to remove the rear crankshaft needle bearings x E12
88 88 6 112 100 112 100 Flywheel lock used to hold flywheel on standard transmission x E12
88 88 6 112 210 Seal guide used o guide crankshaft seals during instalation x E21, E23, E24
88 88 6 121 080 121 080 Ignition wire repair kit used to repair ignition wires. Replaces 112 090 x E36
88 88 6 130 110 130 110 Sampkler tubes 04 14 92 used to test CO levels with Gas Bench x S14
88 88 6 134 030 Current Generator 04 16 85 required for basic adjustment of the idle control valve x E23, E28, E24
88 88 6 135 320 135 320 Socket 04 01 84 used to R&R injectors x 524TD
88 88 6 135 380 135 380 Adapter hose 04 01 84 used to check inj. pump pressure x 524TD
88 88 6 170 006 170 006 Cap adapter 04 25 86 This tool has been replaced by 170 007. PN 88 88 6 170 006 must not be used and must be scrapped. x E32
88 88 6 212 100 Mandrel Used to center the clutch disc while installing the clutch. 265 & 280 5 speed gearbox, 240,260 and 265., 265
88 88 6 231 000 231 000 Installer 5 used to install gearbox housing bearings x E30, E28, E21, E12
88 88 6 231 320 231 320 Holding wrench 04 03 84 6 used to hold output flange to remove nut x E24, E23
88 88 6 231 370 Drift 6 used to install radial oil seal Getrag trans x E28, E21, E30, E23
88 88 6 232 150 Bearing installer 6 used to install front tapered roller bearing in 260 and 245 trans x E32, E34, E36
88 88 6 240 030 240 030 Pressure adapter 6 used to test main oil pressure on 4HP 22 transmission x E32, E30
88 88 6 240 050 Puller 6 used to remove sealing plugs in 3HP 12/20/22 and 4HP 22/24 x E21, E30, E32, E12
88 88 6 240 090 Drift 6 used to install radial oil seal 4HP22/24 x E32, E36, E34, E30
88 88 6 240 110 240 110 Seal installer 04 09 90 6 used to install front radial oil seal on 4HP22/24 transmissions x E30
88 88 6 240 130 Transmission adapter 04 17 87 used to adapt 4hp 22 and 4HP 24 to stand E31, E32, E30
88 88 6 240 150 Transmission holder used to hold 4HP 22/24 x E34, E31, E39, E30, E32, E38, 3HP12,20,22, A4S270R, E36
88 88 6 240 190 flange holder 04 23 92 used to hold the output flange x A5S560Z
88 88 6 243 140 Pump turner 6 used to turn oil pump on 3HP 12/22 x E30, E12, E31, E21, E28, E34, E32, E23, E24
88 88 6 244 044 244 044 Hold down bolts 04 17 87 6 used to check torque converter for leaks E31, E30
88 88 6 244 090 244 090 seal installation tool 04 23 92 used to install the output shaft seal with 005 500 x A5S560Z
88 88 6 244 100 244 100 input shaft seal tool 04 23 92 used to install the input shaft seal x A5S560Z
88 88 6 244 110 244 110 spanner socket 04 23 92 used to remove the spanner nut on the output shaft x A5S560Z
88 88 6 245 150 245 150 Alignment pins 04 12 90 7 used to center valve body on THMR 1 x E36, E34
88 88 6 245 190 Pressure adapter 04 12 90 7 used with 88 88 6 240 021 to test main pressure on THMR 1 trans. x E34, E36
88 88 6 245 200 Driving mandrel 04 12 90 7 used to replace the radial seal onthe THMR 1 shift shaft x E34, E36
88 88 6 245 210 Holder 04 22 92 7 used to R&R the trans shift cable on the 4HP 22/24, A5S 310R/Z x E31, E32, E30
88 88 6 245 300 245 300 Transmission cradle 04 01 91 used to support trans. E36, E34
88 88 6 246 010 246 010 9 Pin test cable 04 26 91 used with 88 88 6 611 459 to test THMR-1 x E36
88 88 6 261 060 261 060 46mm wrench 04 23 87 used to R&R propeller shaft nut 325IX
88 88 6 271 000 271 000 Fixture 04 23 87 used to mount transfer case on stand 325IX
88 88 6 271 090 271 090 Seal driver 04 23 87 used to install seals into the transfer case/rear output shaft x 325IX
88 88 6 271 120 271 120 Sleeve 04 23 87 used with 88 88 6 231 300 to pull output shaft into rear transfer case 325IX
88 88 6 271 160 271 160 Bushing driver 04 23 87 used to install the bushing in the input shaft of the transfer case x 325IX
88 88 6 271 190 271 190 Installer 04 23 87 used to install trnsfer case mounts 325IX
88 88 6 311 050 Sleeve 7 used to remove rubber bushings from front struts x E24, E28
88 88 6 311 110 Puller 7 used to remove tie rod end x E24, E28, E23
88 88 6 312 070 312 070 Thrust sleeve 04 23 87 used with 88 88 6 312 090 to press out front wheel bearings x 325IX
88 88 6 312 080 312 080 Socket 46 mm 7 used to R&R front wheel bearing x E34, E28, E24, E23
88 88 6 312 090 Drive flange extractor 04 23 87 used with 88 88 6 331 307 to press out the flange from the front wheel bearings x E30, 325IX
88 88 6 312 100 Puller 7 used to remove front wheel bearing unit x E30, E32, E28, E24, E31
88 88 6 313 116 take up plate 04 06 82 used to replace coil springs- no longer used x e28
88 88 6 313 117 Holding fixture 04 23 87 used with 88 88 6 313 110/115 to hold spring strut during replacement x 325IX, E30
88 88 6 313 130 Sleeves used to R and R rubber bushing on the wishbone support x E30,E34,E36
88 88 6 313 150 Wrench 8 used to R&R strut nut x E21, E28, E30, E24, E23
88 88 6 313 160 313 160 Wrench 8 used to R&R strut nut x E12
88 88 6 313 170 Wrench 8 used to R&R strut nut x E21, E34, E28, E30, E32
88 88 6 315 000 315 000 Fixture 04 23 87 for mounting front axle final drive on stand 352IX
88 88 6 315 010 315 010 Puller/adapter 04 23 87 used to press off the output shaft on the front axle drive x 352IX
88 88 6 315 020 315 020 Seal driver 04 23 87 used to install oil seal onto the input shaft of the front axle final drive x 325IX
88 88 6 315 030 315 030 Seal driver 04 23 87 used to install output shaft seal on front axle drive x 325IX
88 88 6 315 040 315 040 Washer 04 23 87 used to preload shaft gears in final drive 325IX
88 88 6 315 050 315 050 Thrust sleeve 04 23 87 used to install roller bearing in differential case 325IX
88 88 6 315 060 315 060 Shaft adaptor 04 23 87 used with 88 88 6 002 000 to turn front axle when checking torque 325IX
88 88 6 315 070 315 070 Measuring tool 04 23 87 Used to check front axle drive pinion distance 325IX
88 88 6 315 080 315 080 Gauge disc 04 23 87 used with 88 88 6 002 510 to check front axle drive 325IX
88 88 6 315 090 315 090 Puller 04 23 87 used to remove tappered bearings in front axle drive 325IX
88 88 6 315 100 315 100 Installer 04 23 87 used to install outer race in bearing 325IX
88 88 6 322 040 322 040 Puller 8 used to remove tie rod ends x E24
88 88 6 322 050 Puller 8 used to remove outside tie rod x E21, E23, E31, E28
88 88 6 322 070 322 070 Puller 8 used to remove center tie rod x E12
88 88 6 331 010 Holder 9 used to hold rear axle x E28, E30
88 88 6 331 190 331 190 Drift 9 used to install output flange oil seals x E24, E23
88 88 6 331 200 Drift 9 used to install output flange oil seals on 8 bolt differentials x E24, E23, E32
88 88 6 331 230 Drift 9 used to install output flange oil seals on 6 bolt differentials x E23, E28
88 88 6 331 270 Drift 04 01 83 used to install final drive flange sealing ring x E30
88 88 6 331 280 Drift 04 07 91 used to install the rear seal on the axle flange x E36
88 88 6 331 340 Installer 9 used to install drive pinion x E28, E23, E34, E32, E24
88 88 6 331 360 Puller 10 used to R&R outer race in rear diff. x E28, E213, E30, E24
88 88 6 333 040 333 040 Sleeve 10 used to R x E34
88 88 6 333 080 Accumulator wrench 04 32 92 used to R and R the H31 accumulator All
88 88 6 333 100 Bushing tool 10 used to R&R rear axle rubber bushings x E32, E31, E23, E34, E24
88 88 6 333 190 Press 04 13 90 used to press bushings of front upper control arms E31
88 88 6 333 250 flange press 04 13 90 for pressing the drive flange from the rear wheel bearing x E31
88 88 6 334 000 Support used to support rear axle flange x E24, E23, E32, E28
88 88 6 334 020 Support used to support wheel bearing when inserting axle shaft x E28, E30, E32, E23, E24
88 88 6 334 030 Puller used to R&R rear wheel bearing x E28, E34, E24, E23, E32
88 88 6 334 060 Drift 11 used to install locking plate on rear axle shaft x E23, E24, E28
88 88 6 334 080 Adapter 11 used with 231 300 to insert rear axle shaft x E23, E28, E24
88 88 6 341 020 341 020 Socket 7mm 12 used to remove front brake calipers x E28, E24
88 88 6 341 030 Wrench 12 used to adjust handbrake cable x E23, E36
88 88 6 341 280 Vernier Caliper 04 04 88 used to measure brake rotors x All
88 88 6 343 110 Special bleeder wrench 04 08 91 used to bleed the ASC T mineral oil circuit x E31 Newer, E31, E36, E32, E34
88 88 6 345 040 Jumper plug 04 05 86 used to test the ABS system. See SIB 04 10 84 for details x E30
88 88 6 345 050 Jumper plug 04 14 88 used to test ABS. See SIB 04 10 84 for more details x E32
88 88 6 345 150 345 150 Adjusting gauge 04 23 87 used to adjust the ABS pichup sensor x 325IX
88 88 6 521 100 Pivot pin installer 04 32 87 16 used to install seat pivot pin x E24, E30
88 88 6 611 300 611 300 Pliers 04 08 83 13 removes outside mirror x E23
88 88 6 611 451 611 451 26 pin adapter cable- yellow 04 06 88 used with 26 pin BOB to test ZKE IHKA SSM etc. See SIB for details x E32, E30, E28, E23, E24
88 88 6 611 452 26 pin adapter - white 04 06 88 used with 26 pin BOB to test IHKA ZKE SSM etc. See SIB for details x E24, E28, E32, E30, E23
88 88 6 611 453 26 pin adapter cable - blue 04 06 88 used with 26 pin BOB to test IHKA and cluster x E23, E28, E30, E24, E32
88 88 6 611 454 26 pin adapter cable- green 04 06 88 used with 26 pin BOB to test ZKE IHKA K/CC etc. See SIB for details x E24, E30, E28, E23, E32
88 88 6 611 456 V adapter cable 26 pin 04 25 88 used with 26 pin BOB to troubleshoot wiper/wash module. Refer to 04 06 88, 04 12 88 and 04 13 88 for more cables x E32 Newer, E34 Newer
88 88 6 611 457 611 457 26 pin test cable 04 06 88 used with 26 pin BOB to test ZKE x E32
88 88 6 611 458 611 458 Fused test cable 04 06 88 used with 26 pin BOB to safely test vehicle systems x All
88 88 6 611 459 611 459 26 pin break out box 04 06 88 used with adapter cables to test vehicle systems x E23 Newer
88 88 6 611 476 611 476 Fused test lead 04 12 88 used to safely troubleshoot vehicle systems x E32 Newer
88 88 6 611 481 611 481 26 pin adapter cable-green 04 06 88 used with 26 pin BOB to test OBC III and IV x E32
88 88 6 611 482 611 482 26 pin adapter cable - white 04 13 88 used with 26 pin BOB to troubleshoot instrument cluster x E32
88 88 6 611 483 611 483 26 pin adapter cable - Beige 04 13 88 used with 26 pin BOB to troubleshoot instrument cluster x E32
88 88 6 611 484 611 484 26 pin test cable-brown/grey 04 12 88 used with 26 pin BOB to troubleshoot instrument cluster x E32
88 88 6 612 010 612 010 Adapter cable 04 01 90 used to test secondary ignition with 2013. No longer needed x M70, E32
88 88 6 612 020 612 020 frequency simulator cable 04 01 90 used to output cluster speedometer signal x E32
88 88 6 612 040 612 040 Infra-red test cable 04 01 90 used to test IR input signal x E34, E32
88 88 6 612 050 612 050 Servotronic test cable 04 01 90 used to test servotronic signal with multimeter x E34, E32
88 88 6 612 060 612 060 20/15 pin adapter 04 23 89 used with 88 88 6 621 110 to adapt to 15 pin vehicles x All
88 88 6 621 290 20 Pin SRS reset tool 04 22 89 reads out fault codes and resets memory of SRS x E23, E24
88 88 6 641 150 guide sleeve 04 06 85 used to install guide sleeve in evaporative housing x e23
88 88 6 645 090 645 090 A/C clamp 04 14 92 used to hold compressor to R&R clutch bolts x M50, M42
88 88 6 900 301 Fuel injector cleaner 04 07 86 used to clean L-Jetronic or Motronic fuel injectors- 'Bug Sprayer' x All
88 88 6 900 311 Idle control valve 04 14 86 used to test the idle control valve with a multimeter x E30
88 88 6 900 333 Static protection Matt 04 30 87 used to safely exchange E PROMS in control modules x All
88 88 6 930 207 Brake bleeder cap 04 03 82 used to bleed brake system x All Early
90 88 6 000 002 dash drill 04 19 95 used to install the dash stiffening plate. Refer to SIB 51 08 94 x E36
90 88 6 110 320 R&R Bracket 04 07 05 Used to R&R the cylinder head on the engine block. Refer to repair manual section 11 12 100. N52
90 88 6 111 072 111 072 Retaining bracket 04 09 95 used to attach cylinder head to 88 88 6 111 065 x E31 With M73
90 88 6 112 007 112 007 Thrust Bushing 04 07 03 x E66/N73
90 88 6 112 460 Camshaft test jig 04 22 92 shelf used to check camshaft adjustment at 0 degrees x M60
90 88 6 114 270 R&R Fixture 04 07 05 Used to R&R the Valvetronic intermediate lever pressure springs. Refer to repair manual section 11 37 010. x N52
90 88 6 114 360 R&R tool 04 07 05 Used to R&R the vacum pump sealing cp. Refer to repair manual section 1 66 000. N52, N52
90 88 6 114 490 114 490 R&R tool 04 07 05 Used to R&R the wrist pin retaining rings.1. Assembly bracket2. Removal pliers3. Assembly pliers4. Assembly driftRefer to repair manual section 11 25 530 N52, N52, 52
90 88 6 117 270 117 270 Pin Spanner Wrench 04 07 03 x E66/N73
90 88 6 117 310 117 310 Engine support 04 09 95 used to support engine with trans. removed x E31 With M73
90 88 6 118 490 118 490 Compression adapter Used in conjunction with 110 220 to test engine compression. Refer to repair manual section 11 00 039. 2005 new number is 90 88 0 118 490. All
90 88 6 119 455 119 455 Crankshaft Shim 04 07 03 x E66/N73
90 88 6 119 476 119 476 Camshaft Securing Bracket 04 07 03 x E66/N73
90 88 6 121 300 121 300 134 pin B.O.B and adapter cable set 04 14 97 used to diagnose problems in control modules. x E39, E38
90 88 6 121 310 121 310 Multichannel Adapter 04 12 02 Used in conjunction with the DISplus and MFK2 cables to perform automatic engine tests on N62 engines and newer. x E65 and newer
Добавлено через минуту:
90 88 6 126 410 126 410 Adapter lead 04 27 92 Actuates VANOS unit for testing x M50
90 88 6 161 150 161 150 Evap. system leak tester 04 06 97 test for leaks in the evaporative syatem. used in conjunction with 25 bar pressure sensor 04 30 96. x E36
90 88 6 212 150 212 150 self adj. clutch reset tool 04 03 97 used to reset SAC during instillation. x E36, E34
90 88 6 212 200 212 200 Clutch mandrel Used to center the clutch disc. Gs6-37BZ GS6-37DZ
90 88 6 215 030 Clutch bleeder tool 04 12 97 5 used to bleed the clutch slave cylinder E34, E36
90 88 6 230 240 230 240 Drift pin remover Used to remove the transmission gearshift actuator. x E46 with S54, E46 with S54 & SMG
90 88 6 230 490 Transmission seal puller 04 12 97 5 used to remove input shaft seals. x E31, E34
90 88 6 240 250 240 250 Transmission support 04 32 96 used t support A5S 440Z trans. E38
90 88 6 245 250 245 250 Seal installer 04 08 95 15 used to install shift shaft seal on A5S 560Z x E31
90 88 6 245 260 245 260 Seal puller 04 08 95 15 removes shift shaft seal x E31
90 88 6 245 360 245 360 Selector shaft tool Used to R A4S200R,270R,310R,360R,390R
90 88 6 245 490 245 490 Seal Guide 04 08 95 15 protects shift shaft seal during instillation x E31
90 88 6 246 060 246 060 16 pin test cable 04 10 93 used with 88 88 6 611 459 to test trans. circuits E36, E34, E32
90 88 6 312 074 Seat test cable 04 10 98 used to test seat function when removed x E46
90 88 6 312 152 Pressure pad 04 24 01 Replaces 312 152 from SIB 04 01 83. x E46
90 88 6 312 153 Brace 04 24 01 Replaces 312 153 from SIB 04 01 83. x E 46
90 88 6 321 090 Securing ring press 04 01 96 14 used to install steering wheel column securing ring x E32, E34, E31
90 88 6 333 235 Slip Bushing 04 14 03 Used to R&R the front rubber mount on the final drive. x E60
90 88 6 333 420 333 420 Final drive drift 04 19 94 10 used to replace the output shaft seal on the 6 bolt/188 final drive x E32
90 88 6 333 440 333 440 Final drive drift 04 19 94 10 used to replace output shaft seal on 8 bolt/188 final drive x E32
90 88 6 333 450 333 450 Final drive drift 04 19 94 10 used to replace output shaft seal on 8 bolt/210/215 drives x E32
90 88 6 333 470 333 470 Final drive drift 04 19 94 11 installs seal on 6 bolt /188 final drive x E32
90 88 6 334 163 Support Tube 04 14 03 Used to remove the rear rubber mount on the final drive. x E60
90 88 6 334 250 334 250 Drift 04 23 96 11 used to install output flange seal on 220 drive x E38
90 88 6 345 110 ABS/ASC Tester 04 33 92 used to diagnose ABS/ASC in cars without a data link. See SIB for details x E28, E30, E31, E23, E32, E24
90 88 6 347 262 Wheel bearing installer 04 52 00 Used to install the 49mm front wheel bearing. x E53
90 88 6 416 110 Window wrench 04 12 93 used to adjust quarter window x E36, E31
90 88 6 513 190 Door lock plate remover 0423 94 13 replaces 88 88 6 513 140. Releases locking plate x E32, E34, E36, E31
90 88 6 521 010 OC3 Seat occupancy cable 72 02 05 Used to recode the seat occupancy mat. Refer to SI B72 02 05 fo complete details and instructions. x E60,65,66,90,83,85
90 88 6 611 160 6 pin plug remover 04 11 92 used to R x All
90 88 6 611 457 adapter cable 04 13 94 used with 641 160 to test water valves x all since E32
90 88 6 612 040 Seat test cable 04 10 98 used to test elctric seat when removed x E46
90 88 6 612 430 612 430 14 Pin adapter cable 04 12 05 Used to perform measurements on the heating system in conjunction with 611 459. x E90
90 88 6 613 190 613 190 EWSIII test cable 04 02 97 used to diagnose EWS III x E38
90 88 6 613 300 613 300 EWS ring remover 04 15 97 13 used to remove the EWS ring antenna E38, E36
90 88 6 616 001 Wiper arm remover 04 15 97 used to remove the wiper arm E39, E38
90 88 6 619 020 Electrical connector kit #4 04 18 92 Replacement connector parts can be ordered as follows. From ASAP select EPC start, additional information, parts kit, MG83 then search for the replacement part. x E31 Newer
90 88 6 630 400 630 400 Light check module test cable 04 15 96 used to locate faults in light check module x E38
90 88 6 631 000 631 000 Xenon light test cable 04 33 96 used to test Xenon lights x E38
90 88 6 641 120 641 120 Release tool 04 15 94 used to disconnect the bowden cables from the heat/AC panel x E34
90 88 6 641 160 641 160 Test cable 04 13 94 used to test water valve operation while on road test E32 Newer
90 88 6 641 467 Test cable 0413 94 ed to test water valve operation while on road test E32 Newer
90 88 6 651 100 651 100 Radio removal tool 04 15 97 used to remove the C33 radio E38
90 88 6 657 100 657 100 ZAE/MRS Adapter cable 04 26 96 used inconjunction with 88 88 6 614 410 to diagnose ZAE/MRS system x E38
/S62
Добавлено через минуту:
Как пользоваться:
к примеру, ищем приспособу для фиксации валов на M60.
По ТИСу часть приспособы имеет номер 112 430.
Давим в браузере на поиск и вводим туда этот номер.
Находится строчка:
83 30 0 490 886 112 430 Camshaft insertion jig 04 22 92 A22 used to check camshaft possition after insertion x M60
в ней: 83 30 0 490 886 каталожный номер приблуды, который принимает пресловутый экзист (только это один из кусочков, приблуда составная)
т.е. первые 11 цифр номер по каталогам для заказа, а остальные 6 номер инструмента по тису
|
